Table of Contents
Advertisement
Connecting to a Personal Computer
The type of video connections that can be used to connect to a computer depends on the computer's display adapter.
The following table show the typical factory preset signal timing for each connection type. Some display cards may not be able
to support the required resolution for proper image reproduction with the selected connection.
The monitor will show the proper image by automatically adjusting the factory preset timing signal.
<Typical factory preset signal timing>
Scanning frequency
Resolution
Horizontal
640 x 480
31.5 kHz
800 x 600
37.9 kHz
1024 x 768
48.4 kHz
1280 x 720
45.0 kHz
1280 x 768
47.8 kHz
1280 x 800
49.7 kHz
1280 x 1024
64 kHz
1360 x 768
47.7 kHz
1366 x 768
47.7 kHz
1400 x 1050
65.3 kHz
1440 x 900
55.9 kHz
1600 x 1200
75.0 kHz
1680 x 1050
65.3 kHz
1920 x 1080
67.5 kHz
1920 x 1200
74.6 kHz
1920 x 2160
133.3 kHz
3840 x 2160
65.7 kHz
3840 x 2160
67.5 kHz
3840 x 2160
133.3 kHz
3840 x 2160
135.0 kHz
4096 x 2160*
54.0 kHz
3
4096 x 2160*
3
135.0 kHz
*1: Recommended resolution.
*2: Only HBR2 is set.
*3: Compressed image.
Connecting to a Player or Computer with HDMI
•
Please use an HDMI cable with the HDMI logo.
•
It may take a moment for the signal to appear after turning on the computer.
•
Some display cards or drivers may not display an image correctly.
•
When you use a computer with HDMI, please set OVER SCAN to "AUTO" or "OFF" as display drivers may not be fully
compatible and may not display an image correctly (see
•
To output HDMI audio, set [HDMI1], [HDMI2] or [HDMI3] at AUDIO INPUT in the OSD or choose [HDMI1], [HDMI2] or
[HDMI3] by pressing the remote control AUDIO INPUT button.
•
If the source signal is 3840 x 2160 (60 Hz) and 4096 x 2160 (60 Hz), please set MODE2 at HDMI in TERMINAL SETTINGS
(See
page
38).
•
If the monitor's main power is turned on after a connected computer is turned on, sometimes an image is not displayed.
In this case, please turn off the computer then turn it on again.
Connecting to a Computer with DisplayPort
•
Please use a DisplayPort cable with the DisplayPort compliance logo.
•
To use the DisplayPort out connector, please refer to Video out (See
•
It may take a moment for the signal to appear after turning on the computer.
•
When connecting a DisplayPort cable to a component with a signal conversion adapter, an image may not appear.
•
Some DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the lock.
•
To output DisplayPort audio, set [DisplayPort1] or [DisplayPort2] at AUDIO INPUT in the OSD or choose [DisplayPort1] or
[DisplayPort2] by the remote control AUDIO INPUT button.
•
To display individual images at each connected monitors with the DisplayPort OUT connector, please set DisplayPort1.2 and
MST at DisplayPort in the TERMINAL SETTINGS (See
•
If the monitor's main power is turned on after a connected computer is turned on, sometimes an image is not displayed.
In this case, please turn off the computer then turn it on again.
HDMI
Vertical
MIDE1
MIDE2
60 Hz
Yes
Yes
60 Hz
Yes
Yes
60 Hz
Yes
Yes
60 Hz
Yes
Yes
60 Hz
No
No
60 Hz
Yes
Yes
60 Hz
Yes
Yes
60 Hz
No
No
60 Hz
No
No
60 Hz
Yes
Yes
60 Hz
Yes
Yes
60 Hz
Yes
Yes
60 Hz
Yes
Yes
60 Hz
Yes
Yes
60 Hz
Yes
Yes
60 Hz
Yes
Yes
30 Hz
No
No
30 Hz
Yes*
1
Yes
60 Hz
No
Yes
60 Hz
No
Yes*
1
24 Hz
Yes
Yes
60 Hz
No
Yes
English-18
DisplayPort
1.1a
1.2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes*
Yes
1
No
No
No
Yes*
*
1,
2
No
No
No
No
No
No
page
34).
page
68).
page
38).
Advertisement
Table of Contents
