Related Manuals for LG 55EW961H
Summary of Contents for LG 55EW961H
- Page 1 INSTALLATION MANUAL OLED TV* Please read this manual carefully before operating your set and retain it for future reference. EW96** www.lg.com...
-
Page 2: Table Of Contents
LANGUAGE & COUNTRY SELECTION MEDIA SHARE - Automatically for Setup - SmartShare - Manually for Setup - Screen Share - USB LG Smart Install Utility - Media Renderer - Bluetooth Sound Sync INSTALLATION MENU - DIAL - TV Name INTRODUCTION... -
Page 3: Location And Function Of Controls
LOCATION AND FUNCTION OF CONTROLS LOCATION AND FUNCTION OF CONTROLS Parts and Button Screen Remote control and Intelligent sensors Power Indicator Joystick Button Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment. Joystick Button - This button is located below the TV screen. NOTE You can set the power indicator light to on or off by selecting General in the main menus. -
Page 4: Ezmanager
EZMANAGER EZMANAGER • Image shown may differ from your TV. • INTRODUCTION The Pro:Centric Platform enables you to simply install, manage and use guest-centric solutions. The default Domain “procentric.local” and IP Server Address are needed to be registered in DNS TV will contact the IP Server using the default Domain “procentric.local” via IP on server search page. -
Page 5: Language & Country Selection
EZMANAGER LANGUAGE & COUNTRY SELECTION (Except for Iran) - Please select the Language and Country. Some countries need to select the Time Zone. (Only Iran) - Please select the Language. -
Page 6: Automatically For Setup
EZMANAGER Automatically for Setup From the TV Configuration Options screen, you can choose how to proceed with the configuration of this TV. Whether you will configure the TV for Pro:Centric operation via the wizard or use a USB memory device to configure the TV, you may first wish to set the Room Number on the TV. - Page 7 EZMANAGER This step automatically searches for the Pro:Centric Server. If was found the Pro:Centric data channel, select the ‘NEXT’ .
- Page 8 EZMANAGER Downloading the Pro:Centric application files takes few minutes. After the installation is completed, the following screen will be displayed.
-
Page 9: Manually For Setup
EZMANAGER Manually for Setup Select a Label and/or enter the Room Number using the numeric keypad on the remotes or using the virtual keyboard on the TV screen. To continue, move and select ‘NEXT’ . Please select the ‘MANUAL PRO:CENTRIC’ . - Page 10 EZMANAGER Configure the appropriate Pro:Centric settings in the TV.
- Page 11 EZMANAGER Downloading the Pro:Centric application files takes few minutes.
- Page 12 EZMANAGER After the installation is completed, the following screen will be displayed.
-
Page 13: Usb Lg Smart Install Utility
EZMANAGER USB LG Smart Install Utility Select the ‘USB CONFIGURATION’ → ‘TV MANAGER’ . - If you have USB Memory for “LG_DTV” or “lg_dtv” folder, this step shows the USB file list for downloading the items. - Detail information is described in TV Manager chapter of Installation Menu. - Page 14 EZMANAGER Downloading the files takes few minutes. After the installation is completed, the following screen will be displayed.
-
Page 15: Installation Menu
The abundant functions for Hotel TV linked with software installation can be projected on OSD as ‘Installation Menu’ . The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s easy installation and convenient operation for Hotelier and System Integrators. -
Page 16: Hotel Mode Operation
INSTALLATION MENU Hotel Mode Operation - Decide to work all functions of ‘Hotel Mode Operation’ or not by setting ‘Hotel Mode Operation’ as On(Work) or Off(Do Not Work) - When ‘Hotel Mode Operation’ is set to On(Work), all functions of Hotel Mode apply. - When ‘Hotel Mode Operation’... -
Page 17: Key Management
Operation’ will be worked by below. IR Operation y Decide whether work the LG remote control or not. - When ‘IR Operation’ is set to 'Normal' , all remote keys are available. - 'Use PWR Only' makes block all remote keys except power key. -
Page 18: Limited Mode
INSTALLATION MENU Limited Mode - Configure TV function’s limitation. When selected to ‘On’ , following sub-menus will be worked by below. Setup Menu - Permit to tune and manage programmes as 'On'(permitted) or 'Off'(not permitted). Programme Change y Decide to change channel or not by setting ‘Programme Change' as ‘On’(Change Possible) or ‘Off’(Change Impossible) when present source is TV. -
Page 19: Power On Default
INSTALLATION MENU Power On Default - Set the channel to display and Volume Level, etc. when turn on power in AC Power On or Stand-by status. - Set to On(Work) or Off(Do Not Work). - When ‘Power On Default’ is set to Off, it is not applied to the subordinate Input, Programme, A/V Setting, Aspect Ratio menu. -
Page 20: Network
INSTALLATION MENU NETWORK button to select the NETWORK. Use the MAC Address - Displays the MAC address (not customizable). Network Setting One-click network connection - Connects easily to a wired/wireless network. - Network Connection to connect to an available network automatically. Follow the prompts on the TV. To connect to a network through Set Expert - For use in special circumstances such as in offices (in cases where a static IP is used). -
Page 21: Ip Stream Control
INSTALLATION MENU IP Stream Control Audio PTS Offset - Controlling output stream timing of audio. - You can set the '-500~500' (Change step is -10 or +10) Video PTS Offset - Controlling output stream timing of video. - You can set the '-500~500' (Change step is -10 or +10) IGMP - You can set IGMP version. -
Page 22: Mode
INSTALLATION MENU Mode - Sets whether or not enable Pro:Centric and the service method . - You can set to Off, Configuration Only, Flash(Except for Iran), GEM or HTML using the button . The default value is Off; when it is set to Off, all the sub items are disabled. (Except for WORF, Room Number Setting) WORF - Press the ‘OK’... -
Page 23: Media Type
INSTALLATION MENU Media Type - Sets the medium type to RF or IP. The default value is RF. • Data Channel Freq(KHz) • - Sets the RF frequency at which the Pro:Centric data is received. • Data Channel Type • - Sets the RF modulation type to DVB-T or DVB-C. -
Page 24: General
INSTALLATION MENU GENERAL Configuration Setup Select RCU - It is a mode to set whether to use Select RCU or not. When ‘Select RCU’ is set to ‘Enable’ , You can adjust ‘Number of RCU’ menu. Number of RCU - It is a mode to set Number of RCU. Number of RCU value range 1~9. - Page 25 INSTALLATION MENU RS232 DC Power Outlet - It is a mode to decide whether to output DC or not for power supply to IB Box in Installation Menu. We offer a output terminal in one Pin of RS232C Jack for the use of communication. - 5 V DC Power Outlet and 12 V DC Power Outlet must operate mutually exclusively.
- Page 26 INSTALLATION MENU DTV Programme Update - It is a mode to set whether to update DTV programme automatically or not. When DTV Programme Update is set to ’Auto’ , the function to update TV’s programme map according to dtv programme’s stream information.
-
Page 27: External Speaker
INSTALLATION MENU No Signal Image - Set to On or Off. - It is a mode to decide whether to use no signal image when there is no signal. External Speaker Volume Control - Selects the volume control method of an external speaker. You can select ‘Off’... -
Page 28: Power Saving
CEC Mode - You will have 3 modes to choose [Default], [HCEC] and [TVLink-CEC]. - If [Default] is selected, you can use SIMPLINK which is provided in LG TV. Also you can enable and disable SIMPLINK through SIMPLINK MENU. - If [HCEC] is selected, you can use TVLink-HCEC Protocol. For more detailed information, please refer to TVLink-HCEC Protocol document) - If [TVLink-CEC] is selected, TV will not directly work for key input except for power key. - Page 29 INSTALLATION MENU StandBy - Set the sending and receiving scenario of OpStandBy(0x0c) command. - Ths detailed scenario is described on the table below. Send Receive Send Only Receive Only Forced Initialize - This setting will be enabled When CEC mode is set as ‘TVLink-CEC’ - If ‘Enable”...
-
Page 30: Clock Setup
INSTALLATION MENU Clock Setup Clock Source - You can select ‘Off’ , ‘Pro:Centric’ , ‘TV’ , ‘NTP’ , ‘Admin’ by pressing button. - NTP : Clock is synchronized using Network Time Protocol. It's only enabled when network cable is connected. - Admin : It's automatically set to Admin when clock is updated by commercial protocols like TVLink-HCEC, TVLink- Interactive, or HCAP API. -
Page 31: Password Change
INSTALLATION MENU Password Change - To ensure more security, Password can be changed by installers’ own design. Change password by using virtual keyboard. Input the password again for confirmation. PreLoaded App If you want to use a particular app, you can choose from the menu. you can setting each apps activation. You can check or uncheck by pressing ‘OK’... -
Page 32: Media Share
- Allows guests to use the TV to access and view data shared either by wired- DLNA Certified devices connected to the same network as the TV or by wireless LG devices using LG’s SmartShare application with Wi-Fi Direct. Screen Share - Screen Share enables WiFi p2p functions such as Miracast and WiDi. -
Page 33: Dial
INSTALLATION MENU DIAL - With this DIAL service, you can launch the target app at Smart Home Launcher bar without select the target app by remote controller. The target app should be already selected at Installer Menu > General > Preloaded App. TV Name - When other media device(ex: smart phone, desktop, laptop) searching TV, this string was displayed. -
Page 34: Tv Manager
INSTALLATION MENU TV MANAGER USB Download Menu * USB Cloning : An Installer can quickly set up and clone multiple TV sets at a property. These cloned TVs will all have the same Master TV Setup: Public Display Mode Installation Menu settings, User A/V settings and the Channel Map. This newer procedure significantly decreases the installation time that would be necessary if the standard RS-232C method were used instead. - Page 35 INSTALLATION MENU Ez Download - Ez Download is a function that enables users to download the desired items all at once, such as EPK (software update file), TLL, Micom. * EPK files should be copied into the folder named LG_DTV on the USB. - TLL files should be copied to the root folder of the USB.
- Page 36 INSTALLATION MENU Update TV Software - This feature update EPK of TV through the hex file in USB. The target file is located in \LG_DTV folder. - If there are more than two USB memory Device, It is possible to select the USB. - The download sequence is Update TV Software ->...
- Page 37 INSTALLATION MENU Update Micom Software - This feature update MICOM of TV through the hex file in USB. The target file is located in \LG_DTV folder - If there are more than two USB memory Device, It is possible to select the USB. - The download sequence is Update Micom Software ->...
- Page 38 INSTALLATION MENU Import Clone File - Once the internal TV data and its channel map information is written to the USB memory card, the user can start “Import Clone File” process with the data file generated and stored in USB memory card. As previously warned in “Export Clone File” process, the user should not turn TV off nor unplug the USB memory card.
- Page 39 INSTALLATION MENU Export Clone File - "Export Clone File” must be done first before “Import Clone File” process, as it generate the file to be used in “Export Clone File”. While writing is in process, the user must not turn TV off nor unplug the USB memory card. The following images might be slightly different than the OSD image.