Toro SGR-6 Operator's Manual
Stump grinder
Hide thumbs
Also See for SGR-6:
- Operator's manual (20 pages) ,
- Turn manual, spring maintenance manual (5 pages)
Related Manuals for Toro SGR-6
Summary of Contents for Toro SGR-6
- Page 1 Form No. 3429-802 Rev A SGR-6 Stump Grinder Model No. 22600—Serial No. 404320000 and Up Model No. 22600HD—Serial No. 404320000 and Up *3429-802* A Register at www.Toro.com. Original Instructions (EN)
- Page 2 Authorized Service arrester, as defined in Section 4442, maintained in Dealer or Toro Customer Service and have the model effective working order or the engine is constructed, and serial numbers of your product ready.
-
Page 3: Table Of Contents
Safety Improper use or maintenance by the operator or owner g000502 Figure 2 can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay 1. Safety-alert symbol attention to the safety-alert symbol , which means: Caution, Warning, or Danger—personal safety instruction. - Page 4 Stop the machine if necessary repairs before starting the machine. anyone enters the area. • Use only genuine Toro replacement parts. • Never leave a running machine unattended. Always shut off the engine, engage the parking brake, and verify that moving parts have stopped...
-
Page 5: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal117-4979 117-4979 1. Entanglement hazard, belt—stay away from moving parts; keep all guards and shields in place. - Page 6 decal133-8062 133-8062 decal137-4870 137-4870 1. Read the Operator’s Manual. decal132-4004 132-4004 1. Warning, cutting wheel—to adjust the cutting wheel teeth between jobs 1) Loosen the nut; 2) Push the tooth down and rotate it 1/3 turn; 3) Tighten the nut to 68 N·m (50 ft-lb); 4) Proceed with grinding.
-
Page 7: Product Overview
Controls Product Overview Become familiar with all the controls (Figure 3 Figure 6) before you start the engine and operate the machine. Handle-Release Knob The handle on this machine can be folded down for easier transport. Unscrew the handle-release knob from the machine (Figure g025789... -
Page 8: Specifications
Contact Parking Brake your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all The parking brake holds the left wheel from turning to approved attachments and accessories. -
Page 9: Operation
Adding Fuel Operation Note: Determine the left and right sides of the DANGER machine from the normal operating position. In certain conditions, fuel is extremely flammable and highly explosive. A fire or Before you Start explosion from fuel can burn you and others and can damage property. -
Page 10: Performing Daily Maintenance
Filling the Fuel Tank WARNING Park the machine on a level surface and engage Fuel is harmful or fatal if swallowed. the parking brake. Long-term exposure to vapors can cause serious injury and illness. Shut off the engine and allow the engine to cool. •... -
Page 11: Starting The Engine
Starting the Engine Grinding a Stump Move the fuel valve to the O position, all the way to the right (Figure DANGER This machine is capable of amputating hands and feet. • Always wear substantial, slip-resistant footwear. • Stay in the operating position while the machine is running, and keep away from moving parts. - Page 12 each sweep, until you have removed the front portion of the stump to ground level (A through D in Figure 11). Raise the cutting wheel, release the parking brake, and move the machine forward a few centimeters (inches). Engage the parking brake. Repeat steps until you have completely removed the stump (E through H in...
-
Page 13: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Important: You can tip the machine backward or on its side to clean or service it, but no longer than 2 minutes. If you hold the machine in this position for too long, fuel can drain into the crankcase and damage the engine. -
Page 14: Engine Maintenance
Engine Maintenance Place the air channels in the cyclone housing. Insert cyclone housing into position and make sure that it fits in the upper portion. Servicing the Air Cleaner Important: Do not use force; align it in place before fitting the screws. Service Interval: Before each use or daily—Check the air filter (more often in dirty or Secure the cyclone housing using the 3 screws. -
Page 15: Servicing The Engine Oil
Servicing the Engine Oil Servicing the Foam Air-Cleaner Element Wash the foam element using a mild detergent Service Interval: Before each use or daily and water. After the first 20 hours/After the first month Squeeze it dry with a clean cloth. (whichever comes first) Soak it with new engine oil. - Page 16 Changing the Engine Oil Start the engine and let it run for 5 minutes. Note: This warms the oil so that it drains better. Park the machine on a level surface and engage the parking brake. Shut off the engine and wait for all moving parts to stop.
-
Page 17: Servicing The Spark Plug
Removing the Spark Plug Park the machine on a level surface and engage the parking brake. Shut off the engine, wait for all moving parts to stop, and allow the engine to cool. Locate and remove the spark plug (Figure 18). -
Page 18: Fuel System Maintenance
Installing the Spark Plug Fuel System Maintenance Cleaning the Sediment Cup Service Interval: Every 100 hours Yearly or before storage Underneath the fuel valve is a sediment cup to catch dirt in the fuel. Park the machine on a level surface and engage the parking brake. -
Page 19: Cooling System Maintenance
Cooling System Turn the fuel valve to the O position, all the way to the right, and check for leaks. Maintenance Note: If it leaks, replace the O-ring. Cleaning the Engine Screen Service Interval: Before each use or daily Before each use, remove any buildup of grass, dirt, or other debris from the engine screen. -
Page 20: Belt Maintenance
Belt Maintenance Checking the Drive-Belt Tension Service Interval: Every 25 hours Note: Replace the belt if it shows any signs of wear, cracks, or damage. g244102 Park the machine on a level surface and engage Figure 24 the parking brake. 1. -
Page 21: Replacing The Drive Belt
Grinder Maintenance Turn the square head adjusting bolt on the frame clockwise to tighten the belt; turn it counter clockwise to loosen the belt. Replacing the Teeth Important: Important: Make sure to tighten all engine bolts after proper belt adjustment Service Interval: Before each use or daily—Check is achieved. -
Page 22: Cleaning
Cleaning Removing Debris from the Machine Regular cleaning and washing increases the life span of the machine. Clean the machine directly after use, before the dirt hardens. Before cleaning, check that the fuel-tank cap is properly in place to avoid getting water in the tank. Use care when using a high-pressure sprayer, because it can damage warning decals, instruction signs, and the engine... -
Page 23: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The engine does not start. 1. The safety bail is in the O position. 1. Hold the safety bail against the handle. 2. If your model is equipped with an 2. Move the switch to the O position. - Page 24 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.