NEC MultiSync LCD3090WQXi User Manual page 24
Hide thumbs
Also See for MultiSync LCD3090WQXi:
- Specifications (2 pages) ,
- Product dimensions (1 page) ,
- User manual (34 pages)
Table of Contents
Advertisement
Tag6
Color Control
Tag7
Sharpness
DVI Selection
HDCP CONTENT
(Digital Input Only)
Video Detect
Off Timer
OFF MODE
OFF MODE Setting
01_English
Color Control Systems: Seven preset color settings.
For preset settings 1, 2, 3 and 5, the following levels can be adjusted:
TEMPERATURE: Adjust the white temperature by increasing or decreasing this setting.
A lower color temperature will make the screen reddish and a higher color temperature
will make the screen bluish.
WHITE (White Balance): If TEMPERATURE needs further adjustment; the individual
R/ G/ B/ levels of the white point can be adjusted. To adjust the R/G/B levels, CUSTOM
must be showing as the TEMPERATURE selection.
HUE: Adjusts the hue of each color*
the menu color bars will show the amount of adjustment.
SATURATION: Adjusts the color depth of each color*
the color vividness increases.
OFFSET: Adjusts the color brightness of each color*
color Brightness increases.
*1: RED, YELLOW, GREEN, CYAN, BLUE and MAGENTA.
NATIVE, sRGB: Original color presented by the LCD panel that is unadjustable.
PROGRAMMABLE: The color tone that was set up with the special application software
is reflected.
This is a digital capability for keeping a crisp image at all signal timings. It continuously
adjusts to maintain as distinct or as soft an image as you prefer and is set independently
according to different timings. Press "Left" or "Right" to adjust.
This function selects the DVI input mode. When the DVI selection has been changed, you
must restart your computer. Press "Left" or "Right" to select.
AUTO: By using the DVI-D to DVI-D cable, the DVI SECTION is DIGITAL.
By using the D-SUB to DVI-A cable, the DVI SECTION is ANALOG.
DIGITAL: DVI digital input is available.
ANALOG: DVI analog input is available.
Selects the type of input to be used with HDCP CONTENT.
OFF: When a PC or other computer equipment is connected, select "OFF".
ON: When a DVD player or other type of high definition device is connected, select "ON".
Note: Interlaced signals (480i, 576i, 1080i) are not supported. If you have any problems,
please refer to the Troubleshooting section of this User's Manual.
Selects the method of video detection when more than one computer is connected.
Press "Left" or "Right" to select.
FIRST: When current video input signal is not present, then the monitor searches for a
video signal from the other video input port. If the video signal is present in the other port,
then the monitor switches the video source input port to the new found video source
automatically. The monitor will not look for other video signals while the current video
source is present.
LAST: When the monitor is displaying a signal from the current source and a new
secondary source is supplied to the monitor, then the monitor will automatically switch to
the new video source. When current video input signal is not present, then the monitor
searches for a video signal from the other video input port. If the video signal is present in
the other port, then the monitor switches the video source input port to the new found
video source automatically.
NONE: The Monitor will not search the other video input port unless the monitor is
turned on.
Monitor will automatically turn off after the preset time period from power on with the
ON/OFF function. When you select "ON", press "SELECT" and "Left" or "Right" to adjust.
Before powering off, a message will appear on the screen asking the user if they want to
delay the turn off time by 60 minutes. Press any OSD button to delay the turn off time.
This function allows the monitor to enter into a power saving mode after
a period of inactivity. The OFF MODE has three settings.
OFF: Monitor does not go into power save mode when the input signal is lost.
STANDARD: Monitor enters power save mode automatically when the input signal is lost.
OPTION: Monitor enters power save mode automatically when the amount of surrounding
light goes below the level that is determined by the user.
Adjusts the ILLUMINANCE value for OFF MODE.
18
1
. The change in color will appear on screen and
English-18
1/25/08, 8:53 AM
1
. Press the "RIGHT" button and
1
. Press "RIGHT" button and the
- Quick Links:
- Quick Start
- Menu Tools
- Appendix
Hide quick links:
Advertisement
Chapters
Table of Contents
