Honeywell MX7 Tecton User Manual
Hand-held computer battery charger user's guide
Hide thumbs
Also See for MX7 Tecton:
- Reference manual (366 pages) ,
- User manual (354 pages) ,
- Quick start manual (13 pages)
Related Manuals for Honeywell MX7 Tecton
Summary of Contents for Honeywell MX7 Tecton
- Page 1 MX7 Tecton Hand-Held Computer Microsoft® Windows® Embedded CE 6 Operating System Microsoft® Windows® Mobile 6.5 Operating System Battery Charger User's Guide...
-
Page 2: Limited Warranty
Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII. -
Page 3: Table Of Contents
Table of Contents Chapter 1: Introduction About this Guide Setup Overview Cautions and Warnings Battery Charger Lithium-Ion Battery Pack Components Installation Assemble the Power Supply Setup Mounting Charging Batteries Inserting a Battery into the Charging Pocket Remove the Battery from the Charging Pocket Interpreting the Charging Pocket LEDs RED Continuous - on any charge pocket RED FLASHING - on any charge pocket... - Page 4 Extending Battery Life Self-Discharge Maintenance Routine Label the Batteries A Simple Battery Usage Routine Sample Log for Battery Maintenance Chapter 3: Technical Assistance...
-
Page 5: Chapter 1: Introduction
This device cannot charge/recharge coin cell batteries sealed inside the mobile device, if any. About this Guide This MX7 Tecton Battery Charger User's Guide is intended to familiarize the user with the safety and operating instructions necessary to use the MX7 Tecton Battery Charger (Model MX7390CHARGER, MX7391CHARGER) to charge rechargeable lithium-ion battery packs (MX7A380BATT, MX7A381BATT, MX7392BATT, MX7393BATT, MX7A396BATT) . -
Page 6: Cautions And Warnings
Do not store the Li-Ion battery pack in direct sunlight or anywhere the battery pack cannot cool down. If the Li-Ion battery pack is hot after removal from the MX7 Tecton, allow it to cool at room temperature or in a cool air stream before placing it in the charger. -
Page 7: Components
Components 1. Front 2. Battery Charging Pocket 3. LED Indicator 4. Power Connection Location 5. LED Function Legend 1. Battery Charging Pocket 2. Retaining Clip 3. Battery Charging Contacts... -
Page 8: Installation
Installation Assemble the Power Supply Assemble the AC adapter for the MX7 Tecton Battery Charger before connecting it to the charger. The AC power supply for the battery charger is shipped with the battery charger. Contact Technical Assistance if there is no AC cable. -
Page 9: Setup
Setup Prerequisite: The AC Adapter is assembled and receiving AC power. The battery charger should be located in an area where it: Is well ventilated. Is not in high traffic areas. Locates or orients the AC cord so that it will not be stepped on, tripped over or subjected to damage or stress. Has enough clearance to allow easy access to the power port on the back of the device. -
Page 10: Mounting
Mounting The battery charger should be located in an area where it: Is well ventilated. Is not in high traffic areas. Locates or orients the AC cord so that it will not be stepped on, tripped over or subjected to damage or stress. Has enough clearance to allow easy access to the power port on the back of the device. -
Page 11: Charging Batteries
Charging Batteries MX7392BATT / MX7393BATT / MX7396BATTERY MX7A380BATT / MX7A381BATT New batteries should be charged fully before first use. The life and capacity of a Lithium Ion battery pack can vary significantly depending on the discharge current and the environment in which it is used. When a battery is placed in a charging pocket, the battery charger begins charging the battery. -
Page 12: Inserting A Battery Into The Charging Pocket
Inserting a Battery into the Charging Pocket Caution! It is important that battery packs are inserted into the charging pocket correctly. Inserting the battery incorrectly could result in damage to the battery pack or the charger. Caution! Do not “slam” the battery pack into the charging pocket. Damage may result. When preparing the battery pack for insertion into the battery charging pocket, hold the battery with its four charging contacts in line with the charging contacts in the charging pocket. -
Page 13: Interpreting The Charging Pocket Leds
Interpreting the Charging Pocket LEDs The status of the charge operation is indicated by the color of the LED for each charging pocket. RED Continuous - on any charge pocket Continuous red means the battery pack is charging. RED FLASHING - on any charge pocket Battery pack fault or failure. -
Page 14: Battery Charger Help
The following is intended as an aid in determining whether the battery pack or the charger may be malfunctioning: Problem Cause Solution Check if the MX7 Tecton battery pack has Honeywell part number MX7A380BATT / MX7392BATT or a Low Different manufacturer's battery pack, Battery pack does not... - Page 15 Problem Cause Solution Make sure that the battery pack temperature is within LED is flashing RED at The charger’s timeout period has specification and retry charging. Contact Technical any pocket. expired. Assistance if problem repeats, for battery pack replacement options. The battery pack voltage has not LED is flashing RED at Contact...
-
Page 16: Charger Cleaning, Storage And Service
Charger Cleaning, Storage and Service Cleaning Unplug the charger from the power source before cleaning or removing debris from charging pockets. Use only mild detergent with a slightly damp cloth to clean the outside of the charger. Do not use solvents or flammable cleaners. -
Page 17: Battery Cleaning, Storage And Service
Battery Cleaning, Storage and Service Cleaning The battery pack should not require cleaning unless it has become heavily soiled. Old or damaged batteries should be disposed of promptly and properly. The best way to dispose of used batteries is to recycle them. Battery recycling facilities recover the Nickel, Lithium or Lead from old batteries to manufacture new batteries. -
Page 18: Technical Specifications
Technical Specifications Electrical Note: Battery packs may leak up to 1mA current through the battery contacts when left in an unpowered battery charger charging pocket. Parameter Minimum Maximum Note Power Supply Input Voltage (V AC-IN) 100 VAC 240VAC Auto-switching Power Supply Input Frequency (freq) 47Hz 63Hz Temperature... -
Page 19: Chapter 2: Set Up A Battery Maintenance Routine
Chapter 2: Set up a Battery Maintenance Routine Introduction The MX7 Tecton uses a 2200 mAh or 1250mAh battery. Minimum battery life is 500 charge/discharge cycles before replacement. Hand held devices and body worn devices use Lithium Ion (Li-Ion) main battery packs that are lightweight and relatively small. -
Page 20: Maintenance Routine
Maintenance Routine Managing your batteries with a battery maintenance routine is intended to ensure: You get as much battery life as you can. You need fewer batteries per shift. Every shift has fully charged batteries. There is a battery slot on the charger for each battery at the end of every shift. All unused batteries are placed in a charger at the end of every shift. -
Page 21: A Simple Battery Usage Routine
3. Users place all used batteries into battery chargers at the end of every shift. 4. Track battery capacity readings by recording the date of last charge for each battery on the label (or log sheet). Sample Log for Battery Maintenance MX7 Tecton Main Battery Charger (MX7 Tecton Battery Charger) -
Page 23: Chapter 3: Technical Assistance
Limited Warranty Honeywell International Inc. ("HII") warrants its products to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any HII product which is (i) improperly installed or used;... - Page 24 The duration of the limited warranty for the MX7 Tecton Battery Charger is 1 year. The duration of the limited warranty for the MX7 Tecton 2200mAh Li-Ion and 1250mAh Li-Ion Battery is 6 months. The duration of the limited warranty for the MX7 Tecton AC power supply and cables is 1 year.
- Page 26 Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com E-EQ-MX7TCHGROG Rev E 10/12...