Table of Contents
Advertisement
Adjustment of the Clock Frequency/Clock Phase
(AUTO PICTURE)
When AUTO PICTURE is set to ON, normally the clock
frequency adjustment and the clock phase adjustment are not
necessary, but this adjustment should be made when the au-
tomatic adjustment cannot be made correctly.
Make the adjustment when a new signal has been input, when
vertical lines appear blurry, or if the image appears unclear.
H-POSITION 1,2 and V-POSITION 1,2 are not available at
the time of RGB input when AUTO PICTURE is turned on.
To adjust H-POSITION 1,2 and V-POSITION 1,2 at the
time of RGB input, turn off AUTO PICTURE.
1. Align the cursor with icon (6)
The cursor is moved left and right with the POSITION
CONTROL /
buttons.
AUTO PICTURE adjustment screen
Icon (6)
AUTO PICTURE : ON
INPUT MODE
RGB MODE
2. Align the cursor with AUTO PICTURE and set to OFF.
AUTO PICTURE: Automatically adjusts the screen
position, clock frequency, and clock phase when ON.
* The cursor is moved up and down with the POSITION
CONTROL
/
buttons.
AUTO PICTURE : ON
INPUT MODE
RGB MODE
AUTO PICTURE: ON/OFF
Select with POSITION CONTROL
There is a transition to the screen below only when OFF.
Note:
•The Picture ADJ and Fine Picture features are
available only when the Auto Picture is off. The Picture
ADJ and Fine Picture features are not available for
Video or S-Video source.
•When the Auto Picture is on, the Picture ADJ and Fine
Picture adjustments are made automatically.
•The Picture Adjustment control allows you to fine tune
the computer image or to remove vertical banding that
might appear. This function adjusts the clock
frequencies that eliminate banding in the image.
•The Fine Picture adjusts the clock phase or reduces
video noise, dot interference or cross talk. (This is
evident when parts of the image appear to be
shimmering.) The Fine Picture adjustment may be
: 4
3
X
: STILL
: 4
3
X
: STILL
/
buttons.
necessary when you connect your computer for the first
time and you have a blurred picture on the screen.
•If the displayed image is small with respect to the
original number of horizontal pixels (including cases
when the display area/lit area is small) when AUTO
PICTURE is turned on, it may take up to 6 seconds for
the image to be displayed.
3. Align the cursor with the desired item using the
POSITION CONTROL
AUTO PICTURE : OFF
INPUT MODE
RGB MODE
PICTURE ADJ
FINE PICTURE
WIDE MODE
Clock phase adjustment
Clock frequency adjustment
INPUT MODE: 4
Select with the POSITION CONTROL
Selecting Native Resolutions for 848 x 480, 852 x 480
and 640 x 480 input signals
There are two controls in the Plasma monitor OSM menus
that allow you to set the monitor to display resolutions
with 848, 852 and 640 horizontal dots in their true
resolutions.
When inputting an 848 x 480 signal, align the cursor at the
top of the OSM window. Move the cursor down to WIDE
MODE and use the POSITION LEFT/RIGHT control to
select 4 x 3. The monitor will display the signal at 848 x
480. If FULL is selected, the monitor will automatically
expand the input signal to 853 x 480.
To choose between 640 x 480 and 852 x 480 resolutions
align the cursor with icon 6 (auto) at the top of the OSM
window, move the cursor down to INPUT MODE and...
Use the POSITION LEFT/RIGHT control to select 16 x 9
to display 852 x 480 in true resolution or to expand
(stretch) 640 x 480 to fill the screen from left to right.
Select 4 x 3 to display 640 x 480 resolution in its standard
4:3 aspect ratio with vertical letterbox bars to the right and
left of the image.
After selecting the desired setting, go to the Auto menu,
set auto picture to OFF and use the Picture Adjust and
Fine Picture controls to adjust clock phase and frequency
to sharpen the image, if necessary.
E-34
buttons .
/
: 4
3
X
: STILL
: NORMAL
3 / 16
9
X
X
/
buttons.
Advertisement
Table of Contents
