Honeywell 2020-5 User Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Barcode Reader
  5. 2020-5
  6. User manual

Honeywell 2020-5 User Manual

Cordless system
Hide thumbs
Table of Contents

Advertisement

Quick Links

2020/3820/3820i
Cordless System
User's Guide
™

Advertisement

Table of Contents
loading

Related Manuals for Honeywell 2020-5

Summary of Contents for Honeywell 2020-5

  • Page 1 2020/3820/3820i Cordless System User’s Guide ™...
  • Page 2 The information in this publication does not represent a commitment on the part of Honeywell. Honeywell shall not be liable for technical or editorial errors or omissions con- tained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
  • Page 3 Caution: Any changes or modifications made to this equipment not expressly approved by Honeywell may void the FCC authorization to operate this equipment. Use only shielded data cables with this system. This unit has been tested with cables less than 3 meters.
  • Page 4 5627 BT Eindhoven The Netherlands Honeywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive. This equipment is intended for...
  • Page 5 If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste administration. You may also contact your supplier for more information on the environmental performances of this product. Germany If your product is marked with the GS symbol, then the product has been issued a GS certificate showing compliance to EN 60950-1, Second Edition.
  • Page 6 Brazil (3820i, 2020-5 Scanner and AP-010BT) This product is approved by Anatel, according to the procedures regulated by Resolution No. 242/2000 and meets the technical requirements applied. Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução No. 242/2000 e atende aos requisitos técnicos aplicados.

  • Page 7: Solids And Water Protection

    • Do not disassemble or modify batteries. Caution: Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the recycle program for batteries as directed by the governing agency for the country where the batteries are to be discarded.
  • Page 8 Required Safety Labels Scanner Compliance Label locations Item Number, Serial Number and Revision Information location...
  • Page 9 Base Compliance Label locations Item Number, Serial Number and Revision Information location...

  • Page 11: Table Of Contents

    Table of Contents Chapter 1 - Getting Started About This Manual ............1-1 Unpacking the System ..........1-1 Models................. 1-1 Cordless System: Main Components ......1-2 About the Battery ............1-2 Proper Disposal of the Battery ......1-3 Base Charge Mode ............ 1-4 Linking Image Scanner to Base ........
  • Page 12 Beeper and LED Sequences and Their Meaning ..1-14 3820/3820i LED Sequences and Their Meaning . 1-15 2020 LED Sequences and Their Meaning ... 1-15 Basic Operation of the Cordless System ....1-16 System Conditions ..........1-17 Communication Between the Cordless System and the Host ...........
  • Page 13 Connecting the Base with RS-232 Serial Port .... 2-8 RS-232 Baud Rate ..........2-9 RS-232 Word Length: Data Bits, Stop Bits, and Parity............2-9 RS-232 Handshaking .......... 2-10 Host ACK Selection..........2-11 Host ACK Enable ..........2-12 Wand Emulation ............2-14 Wand Emulation Connection.......
  • Page 14 Output Sequence Overview........3-10 Output Sequence Editor ........3-11 Require Output Sequence ........3-11 Multiple Symbols............3-13 No Read..............3-14 Video Reverse ............3-14 Chapter 4 - Data Editing Prefix/Suffix Overview..........4-1 To Add a Prefix or Suffix: ........4-1 To Clear One or All Prefixes or Suffixes: ....
  • Page 15 Message Length............6-2 Codabar ..............6-3 Codabar Start/Stop Characters ......6-3 Codabar Check Character........6-3 Codabar Concatenation ........6-4 Codabar Message Length ........6-5 Code 39............... 6-5 Code 39 Start/Stop Characters......6-5 Code 39 Check Character........6-6 Code 39 Message Length ........6-6 Code 39 Append ...........
  • Page 16 UPC A................ 6-18 UPC A Check Digit ..........6-18 UPC A Number System ........6-19 UPC A Addenda ..........6-19 UPC A Addenda Required ........6-19 UPC A Addenda Separator........6-20 UPC-A/EAN-13 with Extended Coupon Code ... 6-20 UPC E0 and UPC E1..........6-21 UPC E0 and UPC E1 Expand......
  • Page 17 Korea Post Code ............6-32 Korea Post Message Length ....... 6-32 PosiCode A and B ............. 6-32 PosiCode Message Length ......... 6-33 Codablock F .............. 6-34 Codablock F Message Length......6-34 Code 16K ..............6-35 Code 16K Message Length......... 6-35 Code 49..............
  • Page 18 Menu Command Syntax ..........10-1 Query Commands..........10-2 Concatenation of Multiple Commands ....10-2 Responses ............10-3 Examples of Query Commands ......10-3 Trigger Commands ............ 10-4 Resetting the Standard Product Default Settings: Current Application Work Group ......10-4 Resetting the Standard Product Default Settings: All Application Work Groups........
  • Page 19 Chapter 13 - Customer Support Product Service and Repair ........13-1 Online Product Service and Repair Assistance... 13-2 Limited Warranty ..........13-2 Appendix A - Reference Charts Symbology Chart............A-1 Code Page Mapping of Printed bar codes ....A-6 Appendix B - Minimizing Bluetooth/ISM Band Network Activity Auto Reconnect Mode...........

  • Page 21: About This Manual

    Product specifications, connector pinouts, a troubleshooting guide, and customer support information are also provided. Honeywell bar code image scanners are factory programmed for the most com- mon terminal and communications settings. If you need to change these set- tings, programming is accomplished by scanning the bar codes in this guide.

  • Page 22: Cordless System: Main Components

    Cordless System: Main Components Battery Contained in Handle About the Battery We recommend use of Hand Held Products Li-ion battery backs. Use of any non-Hand Held Products battery may result in damage not cov- ered by the warranty. Power is supplied to the cordless image scanner by a rechargeable battery that is integrated in the image scanner handle.

  • Page 23: Proper Disposal Of The Battery

    Replace it after the battery is unable to hold an adequate charge. • If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection. Refer to...

  • Page 24: Base Charge Mode

    Base Charge Mode In order for the battery to be charged, there must be enough voltage for the cir- cuitry to work. There are three conditions during which power can be supplied to the base: Condition 1:9VDC power supply connected to the barrel connector Condition 2:12VDC host power source only Condition 3:5VDC host power source only The chart below describes each selection by condition.

  • Page 25: Linking Image Scanner To Base

    Linking Image Scanner to Base When newly shipped or defaulted to factory settings, the base and image scan- ner are not linked. Once the image scanner is placed into the base, the soft- ware automatically links the image scanner and the base. If the image scanner and base have previously been linked, you do not receive any feedback.

  • Page 26: Single Image Scanner Operation

    Single Image Scanner Operation There are two link modes to accommodate different applications: Locked Link Mode and Open Link Mode. Scan the appropriate bar codes included in the Open Link and Locked Link Mode explanations that follow to switch from one mode to another.

  • Page 27: Multiple Image Scanner Operation

    Multiple Image Scanner Operation To put the image scanner in multiple image scanner mode, scan the bar code below. Once you scan this bar code, the image scanner is unlinked from the base and must be placed into the base to re-link. Multiple Image Scanner Operation Note: Multiple Image Scanner Operation Mode allows you to link up to 7 image scanners to one base.

  • Page 28: Changing Image Scanner Name - Via Bar Codes

    (page 1-8 or on the Programming Chart inside the back cover of this man- ual). You may use Barcode Builder, which is included with Quick*View. You may download Quick*View from the Honeywell International Inc. website: at www.honeywellaidc.com 1 - 8...

  • Page 29: Image Scanner Report

    Image Scanner Report Scan the bar code below to generate a report for the connected image scan- ners. The report indicates the port, work group, image scanner name, and address. Image Scanner Report Application Work Groups Your cordless system can have up to seven image scanners linked to one base. You can also have up to seven work groups.

  • Page 30: Application Work Group Selection

    Application Work Group Selection This programming selection allows you to assign an image scanner to a work group by scanning the bar code below. You may then program the settings (e.g., beeper volume, prefix/suffix, data formatter) that your application requires. * Group 0 Group 1 Group 2...

  • Page 31: Resetting The Standard Product Default Settings: Current Application Work Group

    Resetting the Standard Product Default Settings: Current Application Work Group If you aren’t sure what programming options are in your image scanner, or you’ve changed some options and want the standard product default settings restored, scan the Standard Product Default Settings: Current Application Group bar code below.

  • Page 32: Using The Image Scanner With Bluetooth Devices

    Using the Image Scanner with Bluetooth Devices The 3820/3820i image scanner may be used either with the 2020 base or with other Bluetooth devices. Scanning the Non-Base Bluetooth Connection bar code below allows the image scanner to be used with other Bluetooth devices (e.g., PDA, PC - Bluetooth USB Adapter).

  • Page 33: Alarm Sound Type

    and then set the time-out duration (from 0-3000 seconds) by scanning digits on Programming Chart inside the back cover, then scanning Save. Default = 0 sec (no alarm). Base Alarm Duration Image Scanner Alarm Note: If you are out of range when you scan a bar code, you will receive an error beep even if you do not have the alarm set.

  • Page 34: Batch Mode Transmit Delay

    Batch Mode Transmit Delay Sometimes when accumulated scans are sent to the host system, the transmis- sion of those scans is too fast for the application to process. To program a transmit delay between accumulated scans, scan one of the following delays. Note: In most cases, a short (250 ms (milliseconds) delay is ideal;...

  • Page 35: 3820/3820I Led Sequences And Their Meaning

    3820/3820i LED Sequences and Their Meaning LED Indication Beeper Indication Cause Normal Operation Red Flash None Battery low Green Flash 1 beep Successful communi- cation or linking Red, blinking 3 beeps Failed communication Menu Operation Green Flash 2 beeps Successful menu change Red, blinking 3 beeps...

  • Page 36: Basic Operation Of The Cordless System

    The tables below list the indication and cause of the LED illumination and beeps for the 2020. System Condition System Status Indicator (Red LED) Power On/System Idle LED is on Power On/Diagnostic Error Blink LED for long duration, pulsing indefinitely Receiving Data (2020 only) Blink LED for short duration in multiple pulses.

  • Page 37: System Conditions

    RF (Radio Frequency) Module Operation The cordless system uses a state-of-the-art two-way Bluetooth radio to transmit and receive data between the image scanner and the base. Designed for point- to-point and multipoint-to-single point applications, the radio operates using a license free ISM band, which sends relatively small data packets at a fast data rate over a radio signal with randomly changing frequencies, makes the cord- less system highly responsive to a wide variety of data collection applications and resistant to noisy RF environments.

  • Page 38: Communication Between The Cordless System And The Host

    Out of Range and Back into Range with Data Accumulation Mode The image scanner may store a number of symbols (approximately 500 UPC symbols, others may vary) when out of range and then send them to the base when back in range. You will not hear a communication error beep in this mode, but you will hear a short buzz when you pull the trigger if the radio communica- tion is not working.
  • Page 39 2. Disconnect the keyboard cable from the back of the terminal/computer. 3. Connect the appropriate interface cable to the base and to the terminal/ computer and keyboard. Make sure the cables are secured in the wireways in the bottom of the base and that the base sits flat on a...

  • Page 40: Reading Techniques

    Reading Techniques The image scanner has a view finder that projects a bright red aiming beam that corresponds to its horizontal field of view. The aiming line should be centered horizontally over the bar code; it will not read if the aiming line is in any other direction.

  • Page 41: Plug And Play

    Plug and Play Plug and Play bar codes provide instant image scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect. Keyboard Wedge Connection If you want your system programmed for an IBM PC AT and compatibles key- board wedge interface with a USA keyboard, scan the bar code below.

  • Page 42: Wand Emulation Plug & Play

    Wand Emulation Plug & Play In Wand Emulation mode, the image scanner decodes the bar code then sends data in the same format as a wand scanner. The Code 39 Format converts all symbologies to Code 39. The Same Code Format transmits UPC, EAN, Code 128 and Interleaved 2 of 5 without any changes, but converts all other symbologies to Code 39.

  • Page 43: Connecting The Base With Usb

    Each bar code above also programs the following suffixes for each symbology: Symbology Suffix EAN 8 EAN 13 UPC A UPC E Code 39 00 0A 0B Interleaved 2 of 5 00 0D 0B Code 128 * 00 0A 0B Code 128 ** 00 18 0B * Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR-...

  • Page 44: Ibm Surepos

    For additional USB programming and technical information, refer to Honeywell “USB Application Note,” available at www.honeywellaidc.com Note: Without using the 9-volt external, power supply, the base only uses enough power from the host to operate the interface. The image scanner’s battery is not charged when in this mode. Using the 9-volt, external power supply allows the image scanner’s battery to be charged,...

  • Page 45: Usb Hid

    USB Com Port Emulation Scan the following code to program the 3820/3820i to emulate a regular RS- 232-based Com Port. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honey- wellaidc.com .

  • Page 46: Connecting The Base With Serial Wedge

    ACK/NAK Mode ACK/NAK On * ACK/NAK Off Connecting the Base with Serial Wedge The 2020 uses TTL signal levels to wedge into an RS-232 serial network. Use only 2020 serial wedge cables to prevent damage to the base. Refer to Con- necting the Base with RS-232 Serial Port on page 2-8 to set the baud rate and...
  • Page 47 5. Plug the other serial connector into the other device connection and tighten the two screws. 6. Plug the power supply barrel connector to the base, and plug the power supply into the AC source. 7. Once the base has been fully connected, power up the computer. To set up the serial wedge terminal ID, use the serial terminal ID 050 and follow the instructions on page...
  • Page 48 1 - 28...

  • Page 49: Chapter 2 - Terminal Interfaces

    Terminal Interfaces Terminal ID If your interface is not a standard PC AT, refer to "Supported Terminals" on page through page 2-3, and locate the Terminal ID number for your PC. Scan the Terminal ID bar code below, then scan the numeric bar code(s) from the Pro- gramming Chart inside the back cover of this manual to program the image...

  • Page 50: Supported Terminals

    Supported Terminals Terminal Model(s) Terminal ID VT510, 520, 525 (PC style) VT510, 520, 525 (DEC style LK411) Esprit 200, 400 Heath Zenith PC, AT 003* Vectra 003* PS/2 25, 30, 77DX2 AT, PS/2 30–286, 50, 55SX, 60, 003* 70, 70–061, 70–121, 80 IBM 102 key 3151, 3161, 3162, 3163, 3191, 3192, 3194, 3196, 3197, 3471,...
  • Page 51 Supported Terminals Terminal Model(s) Terminal ID Telex 122 key 078, 078A, 79, 80, 191, 196, 1191,1192, 1471, 1472, 1476, 1477, 1482, 1483 USB PC Keyboard 124** USB Mac Keyboard 125** USB Com Port USB HIDPOS 131** Wand Emulation (Code 39 Format) Wand Emulation (Same Code Format) * Default for 2020-5BE.

  • Page 52: Keyboard Country

    Keyboard Country Scan the appropriate country code below to program the keyboard for your country. As a general rule, the following characters are supported, but need special care for countries other than the United States: @ | $ # { } [ ] = / ‘ \ < > ~ * United States Belgium Brazil...
  • Page 53 Keyboard Country (continued) Italy Latin America Netherlands (Dutch) Norway Poland Portugal Romania Russia Slovakia Spain Sweden Switzerland (German) Turkey F Turkey Q U.K. 2 - 5...

  • Page 54: Keyboard Style

    Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock. Default = Regular. Regular is used when you normally have the Caps Lock key off. * Regular Caps Lock is used when you normally have the Caps Lock key on. Caps Lock Shift Lock is used when you normally have the Shift Lock key on (not common to U.S.

  • Page 55: Keyboard Modifiers

    Keyboard Modifiers This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode. Control + ASCII Mode On: The image scanner sends key combinations for ASCII control characters for values 00-1F. Refer to Keyboard Function Relationships, page 7-1 for CTRL+ ASCII Values. Default = Off Control + ASCII Mode On * Control + ASCII Mode Off Turbo Mode: The image scanner sends characters to a terminal faster.

  • Page 56: Connecting The Base With Rs-232 Serial Port

    Connecting the Base with RS-232 Serial Port 1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the base. Note: For the base to work properly, you must have the correct cable for your type of terminal/computer. 3.

  • Page 57: Rs-232 Baud Rate

    RS-232 Baud Rate Baud Rate sends the data from the image scanner to the terminal at the speci- fied rate. The host terminal must be set for the same baud rate as the image scanner. Default = 115,200 . 1200 2400 4800 9600...

  • Page 58: Rs-232 Handshaking

    Parity provides a means of checking character bit patterns for validity. Default = None. 7 Data, 1 Stop, Parity Even 7 Data, 1 Stop, Parity None 7 Data, 1 Stop, Parity Odd 7 Data, 2 Stop, Parity Even 7 Data, 2 Stop Parity None 7 Data, 2 Stop, Parity Odd 8 Data, 1 Stop, Parity Even * 8 Data, 1 Stop, Parity None...

  • Page 59: Host Ack Selection

    transmission, the host sends the XON character (DC1, hex 11). Data transmis- sion continues where it left off when XOFF was sent. Default = RTS/CTS, XON/ XOFF and ACK/NAK Off. RTS/CTS On * RTS/CTS Off XON/XOFF On * XON/OFF Off ACK/NAK On * ACK/NAK Off Host ACK Selection...

  • Page 60: Host Ack Enable

    Commands may be strung together to create custom response sequences. An example of a command string is listed below. 0<ESC>4<ESC>5<ESC>6, The above example will make an image scanner in application work group zero beep low, medium, high. Once Host ACK is enabled, the system works as follows: •...
  • Page 61 2020 Host Escape Commands Command Action <ESC> a Indicate as if successful menu change made <ESC> b Indicate as if unsuccessful menu change made <ESC> 1 Illuminate green LED for 135 milliseconds (followed by at least 70 mSecs. dark time when multiple blinks) <ESC>...

  • Page 62: Wand Emulation

    Wand Emulation Wand Emulation Connection The Wand Emulation Connection bar codes should be used if you want to change the terminal ID only , without changing any other image scanner set- tings. We recommend using Wand Emulation Plug & Play bar codes to pro- gram your image scanner to emulate a wand reader.

  • Page 63: Wand Emulation Transmission Rate

    Wand Emulation Transmission Rate The transmission rate is limited by the terminal’s ability to receive data without dropping characters. Default = 25 inches/second. * 25 Wand Emulation Polarity The Polarity can be sent as standard with black bars high, or reversed with white bars high.

  • Page 64: Wand Emulation Data Block Size

    Wand Emulation Data Block Size This transmits the data in smaller blocks to prevent buffer overflow. Default = 40 . * 40 Wand Emulation Delay Between Blocks This sets the delay time between data blocks. Default = 50ms. * 50ms 150ms 500ms Wand Emulation Overall Checksum...

  • Page 65: Chapter 3 - Output

    Output Image Scanner Functions Good Read Indicators Beeper – Good Read The beeper may be programmed On or Off in response to a good read. Turning this option off, only turns off the beeper response to a good read indication. All error and menu beeps are still audible.

  • Page 66: Beeper Pitch - Good Read

    Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the image scanner emits on a good read. Default = Medium. Low (1600 Hz) * Medium (3250 Hz) High (4200 Hz) Beeper Duration – Good Read The beeper duration codes modify the length of the beep the image scanner emits on a good read.

  • Page 67: Good Read Delay

    Good Read Delay This sets the minimum amount of time before the image scanner can read another bar code. Default = 0 ms (No Delay. ) * No Delay Short Delay (500 ms) Medium Delay (1000 ms) Long Delay (1500 ms) User-Specified Good Read Delay If you want to set your own length for the good read delay, scan the bar code below, then set the delay (from 0-30,000 milliseconds) by scanning digits from...
  • Page 68 Read Time-Out (Serial Trigger Mode) Use this selection to set a time-out (in milliseconds) of the image scanner’s trigger when using serial commands to trigger the image scanner. Once the image scanner has timed out, you can activate the image scanner either by pressing the trigger or using a serial trigger command.

  • Page 69: Automatic Trigger

    If there are no trigger pulls during the “image scanner power time-out timer” interval, the image scanner goes into power down mode. Whenever the trigger is enabled, the “image scanner power time-out timer” is reset. If the image scanner is placed in the 2020 cradle and the battery is in the process of being charged, the image scanner will not go into power down mode.

  • Page 70: Hands Free Time-Out

    Hands Free Time-Out The Automatic Trigger and Presentation Modes are referred to as “hands free” modes. If the image scanner’s trigger is pulled when using a hands free mode, the image scanner changes to manual trigger mode. You can set the time the image scanner should remain in manual trigger mode by setting the Hands Free Time-Out.

  • Page 71: Centering Window

    Centering Window Use the centering feature to narrow the image scanner’s field of view so the image scanner reads only the bar code you want. When centering is turned on, the image scanner only reads codes that intersect or are contained within the centering window you set up.

  • Page 72: Preferred Symbology

    Example: If you have two bar codes next to one another and the centering window is set to 40% left edge and 60% right edge, only the bar code that intersects that window will be decoded. Decoded bar code 100% Preferred Symbology The 3820/3820i can be programmed to specify one symbology as a higher priority over other symbologies in situations where both bar code symbologies...

  • Page 73: Symbology Chart

    High Priority Symbology To specify the high priority symbology, scan the High Priority Symbology bar code below. On the Symbology Chart on page A-1, find the symbology you want to set as high priority. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart (inside back cover).

  • Page 74: Output Sequence Overview

    Output Sequence Overview Require Output Sequence When turned off, the bar code data will be output to the host as the image scanner decodes it. When turned on, all output data must conform to an edited sequence or the image scanner will not transmit the output data to the host device.

  • Page 75: Output Sequence Editor

    5. End Output Sequence Editor Scan F F to enter an Output Sequence for an additional symbology, or Save to save your entries. Other Programming Selections • Discard This exits without saving any Output Sequence changes. Output Sequence Editor Enter Sequence Default Sequence Require Output Sequence When an output sequence is Required , all output data must conform to an edited...
  • Page 76 Output Sequence Example In this example, you are scanning Code 93, Code 128, and Code 39 bar codes, but you want the image scanner to output Code 39 1st, Code 128 2nd, and Code 93 3rd, as shown below. Note: Code 93 must be enabled to use this example. A - Code 39 B - Code 128 C - Code 93...

  • Page 77: Multiple Symbols

    To program the previous example using specific lengths, you would have to count any programmed prefixes, suffixes, or formatted characters as part of the length. If you use the example on page 3-12, but assume a <CR> suffix and specific code lengths, you would use the following command line: SEQBLK62001241FF6A001342FF69001243FF The breakdown of the command line is shown below: SEQBLK sequence editor start command...

  • Page 78: No Read

    No Read With No Read turned On , the image scanner sends an “NR” to the host if you pull and release the trigger without reading a code (e.g., bad bar code). If No Read is turned Off , the “NR” will not be sent to the host. No Read On * No Read Off If you want a different notation than “NR,”...

  • Page 79: Chapter 4 - Data Editing

    Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.

  • Page 80: To Clear One Or All Prefixes Or Suffixes

    Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page 1252) on page A-4, for the prefix or suffix you wish to enter. Step 5. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual.

  • Page 81: To Add A Carriage Return Suffix To All Symbologies

    Step 3. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual or scan 9, 9 for all symbologies. Your change is automatically saved. To Add a Carriage Return Suffix to All Symbologies Scan the following bar code if you wish to add a carriage return suffix to all sym- bologies at once.

  • Page 82: Suffix Selections

    Suffix Selections Add Suffix Clear One Suffix Clear All Suffixes Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the image scanner transmits the function code to the terminal. Charts of these function codes are provided in Supported Interface Keys start- ing on...

  • Page 83: Intercharacter Delay

    Intercharacter Delay An intercharacter delay of up to 495 milliseconds may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of milliseconds and the SAVE bar code using the Programming Chart inside the back cover of this manual.

  • Page 84: Interfunction Delay

    Interfunction Delay An interfunction delay of up to 495 milliseconds may be placed between the transmission of each segment of the message string. Scan the Interfunction Delay bar code below, then scan the number of milliseconds and the SAVE bar code using the Programming Chart inside the back cover of this manual.

  • Page 85: Chapter 5 - Data Formatting

    Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the image scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output.

  • Page 86: Other Programming Selections

    Step 4. Code I.D. In the Appendix A, find the symbology to which you want to apply the data format. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart inside the back cover of this manual.
  • Page 87 ASCII Conversion Chart (Code Page 1252) on page A-4, and nn is the numeric value (00-99) for the number of times it should be sent.) E9 Send all but the last “nn” characters, starting from the current cursor posi- tion. Syntax = E9nn (nn is the numeric value (00-99) for the number of characters that will not be sent at the end of the message.) Move Commands F5 Move the cursor ahead “nn”...

  • Page 88: Data Format Editor

    ters to be replaced and xx defines replacement characters, continuing through zz and zz E5 Terminates character replacement. Syntax = E5. FE Compare character in current cursor position to the character “xx.” If char- acters are equal, increment cursor. If characters are not equal, no format match.

  • Page 89: Alternate Data Formats

    When Data Formatter is required, all input data must conform to an edited for- mat or the image scanner does not transmit the input data to the host device. Data Format On, Format Required Alternate Data Formats Alternate formats allow you “single shot” capability to scan one bar code using a different data format than your primary format.
  • Page 90 5 - 6...

  • Page 91: Introduction

    Symbologies Introduction This programming section contains the following menu selections. Refer to Chapter 10 for settings and defaults. • All Symbologies • Interleaved 2 of 5 • China Post Code • Korea Post Code • Codabar • Matrix 2 of 5 •...

  • Page 92: Message Length

    Message Length You are able to set the valid reading length of some of the bar code symbologies. If the data length of the scanned bar code doesn’t match the valid reading length, the image scanner will issue an error beep. You may wish to set the same value for minimum and maximum length to force the image scanner to read fixed length bar code data.

  • Page 93: Codabar

    Codabar <Default All Codabar Settings> Codabar * On Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit . Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.”...

  • Page 94: Codabar Concatenation

    When Check Character is set to Validate, but Don’t Transmit , the unit will only read Codabar bar codes printed with a check character, but will not transmit the check character with the scanned data. * No Check Character Validate Modulo 16, but Don’t Transmit Validate Modulo 16 and Transmit Codabar Concatenation...

  • Page 95: Codabar Message Length

    Codabar Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60. Minimum Message Length Maximum Message Length Code 39 <...

  • Page 96: Code 39 Check Character

    Code 39, continued Code 39 Check Character No Check Character indicates that the image scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate, but Don’t Transmit, the unit only reads Code 39 bar codes printed with a check character, but will not transmit the check character with the scanned data.

  • Page 97: Code 39 Append

    Code 39, continued Code 39 Append This function allows the image scanner to append the data from several Code 39 bar codes together before transmitting them to the host computer. When this function is enabled, the image scanner stores those Code 39 bar codes that start with a space (excluding the start and stop symbols), and does not immedi- ately transmit the data.

  • Page 98: Full Ascii

    Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #.

  • Page 99: Code 39 Code Page

    Code 39 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting.

  • Page 100: Interleaved 2 Of 5 Message Length

    When Check Digit is set to Validate and Transmit, the image scanner only reads Interleaved 2 of 5 bar codes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit...

  • Page 101: Code 93

    Code 93 < Default All Code 93 Settings > Code 93 * On Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 0-80.

  • Page 102: Straight 2 Of 5 Industrial

    Straight 2 of 5 Industrial (three-bar start/stop) <Default All Straight 2 of 5 Settings> Straight 2 of 5 Industrial * Off Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information.

  • Page 103: Straight 2 Of 5 Iata Message Length

    Straight 2 of 5 IATA, continued * Off Straight 2 of 5 IATA Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length Matrix 2 of 5...

  • Page 104: Matrix 2 Of 5 Message Length

    Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 11...

  • Page 105: Code 11 Message Length

    Code 11, continued Code 11 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 128...

  • Page 106: Isbt 128 Concatenation

    Code 128, continued ISBT 128 Concatenation In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood information in a uniform manner. The use of ISBT formats requires a paid license. The ISBT 128 Application Specification describes 1) the critical data elements for labeling blood products, 2) the current recommendation to use Code 128 due to its high degree of security and its space-efficient design, 3) a variation of Code 128 that supports concatenation...

  • Page 107: Code 128 Function Code Transmit

    Code 128 Function Code Transmit By default, Code 128 function codes are not transmitted with Code 128 bar code data. However, if you wish to transmit Code 128 function codes with the bar code data, scan the Function Codes On bar code, below. * Function Codes Off Function Codes On Telepen...

  • Page 108: Telepen Message Length

    Telepen Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-60. Minimum Default = 1, Maximum Default = 60. Minimum Message Length Maximum Message Length UPC A <Default All UPC A Settings>...

  • Page 109: Upc A Number System

    UPC A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it. Default = On. * On UPC A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC A data.

  • Page 110: Upc A Addenda Separator

    UPC A Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On UPC-A/EAN-13 with Extended Coupon Code Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code.

  • Page 111: Upc E0 And Upc E1

    UPC E0 and UPC E1 Most U.P.C. bar codes lead with the 0 number system. For these codes, use the UPC E0 selection. If you need to read codes that lead with the 1 number sys- tem, use the UPC E1 selection. Default = On (UPC E0) and Off (UPC E1). * UPC E0 On UPC E0 Off UPC E1 On...

  • Page 112: Upc E0 And Upc E1 Addenda Separator

    UPC E0 and UPC E1 Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned off, there is no space. Default = On. * On UPC E0 Check Digit Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not.

  • Page 113: Upc E0 Addenda

    UPC E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC E data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN 13 <Default All EAN/JAN Settings>...

  • Page 114: Ean/Jan 13 Addenda

    EAN/JAN 13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 13 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN 13 Addenda Required When Addenda Required is set to on, the image scanner will only read EAN/...

  • Page 115: Isbn Translate

    ISBN Translate This selection causes EAN-13 Bookland symbols to be translated into their equivalent ISBN number format. Default = Off. * Off EAN/JAN 8 <Default All EAN/JAN 8 Settings> EAN/JAN 8 * On EAN/JAN 8 Check Digit This selection allows you to specify whether the check digit should be transmit- ted at the end of the scanned data or not.

  • Page 116: Ean/Jan 8 Addenda

    EAN/JAN 8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN 8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN 8 Addenda Required When Addenda Required is set to on, the image scanner will only read EAN/...

  • Page 117: Msi

    <Default All MSI Settings> * Off MSI Check Character Different types of check characters are used with MSI bar codes. You can program the image scanner to read MSI bar codes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate and Transmit , the image scanner will only read MSI bar codes printed with the specified type check character, and will transmit this character at the end of the scanned data.

  • Page 118: Plessey Code

    Plessey Code <Default All Plessey Code Settings> Plessey Code * Off Plessey Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length GS1 DataBar Omnidirectional...

  • Page 119: Gs1 Databar Limited

    GS1 DataBar Omnidirectional * On GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited * On GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > 6 - 29...

  • Page 120: Gs1 Databar Expanded Message Length

    GS1 DataBar Expanded * On GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74. Minimum Message Length Maximum Message Length GS1 Emulation...

  • Page 121: China Post Code

    China Post Code <Default All China Post Code Settings> China Post Code * Off China Post Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-80.

  • Page 122: Korea Post Code

    Korea Post Code <Default All Korea Post Code Settings> Korea Post Code * Off Korea Post Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 2-80.

  • Page 123: Posicode Message Length

    You have to have PosiCode A and B on to read any of the PosiCode symbolo- gies. A and B On (No Limited) A and B and Limited A On (Limited B Off) * A and B and Limited B On (Limited A Off) PosiCode Message Length Scan the bar codes below to change the message length.

  • Page 124: Codablock F

    Codablock F <Default All Codablock F Settings> Codablock F * Off Codablock F Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048. Minimum Message Length Maximum Message Length Code 16K...

  • Page 125: Code 16K

    Code 16K * Off Code 16K Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 0-160. Minimum Default = 1, Maximum Default = 160. Minimum Message Length Maximum Message Length Code 49...

  • Page 126: Code 49 Message Length

    Code 49 Message Length Scan the bar codes below to change the message length. Refer to Message Length on page 6-2 for additional information. Minimum and Maximum lengths = 1-81. Minimum Default = 1, Maximum Default = 81. Minimum Message Length Maximum Message Length 6 - 36...

  • Page 127: Chapter 7 - Interface Keys

    Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can be used with the image scanner. Refer to page 2-7 enable Control + ASCII mode. Function Code HEX/ASCII Value Full ASCII “CTRL”...
  • Page 128 The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to US only. The following chart indicates the equivalents of these five characters for different countries. Country Codes United States Belgium < Scandinavia <...
  • Page 129 Supported Interface Keys IBM AT/XT and PS/2 Compatibles, IBM XTs and IBM, DDC, Memorex WYSE PC/AT Compatibles Telex, Harris* ASCII Supported Keys Supported Keys Supported Keys Reserved Reserved Reserved Enter (KP) CR/Enter Enter Cap Lock Caps Lock ALT make Reserved ALT break Reserved CTRL make...
  • Page 130 Supported Interface Keys IBM, Memorex Telex (102)* Memorex Telex (88)** ASCII Supported Keys Supported Keys Reserved Reserved Enter Enter PF10 PF11 PF12 Reserved Reserved New Line New Line Field Forward Field Forward Reserved Tab/Field Forward Field Forward Delete Delete Field Exit New Line Insert Insert...

  • Page 131: Supported Interface Keys

    Supported Interface Keys Esprit 200, 400 Esprit 200, 400 Esprit 200, 400 ANSI ASCII ASCII Supported Keys Supported Keys Supported Keys Reserved Reserved Reserved New Line New Line New Line New Line New Line New Line Delete New Line New Line New Line Insert Escape...
  • Page 132 Supported Interface Keys Apple Mac/iMac ASCII Supported Keys Reserved Enter/Numpad Enter CAPS ALT make ALT break CNTRL make CNTRL break RETURN APPLE make APPLE break RETURN Ins Help Home Prnt Scrn BACKSPACE LSHIFT TAB BACKSPACE 7 - 6...

  • Page 133: Chapter 8 - Utilities

    Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Chart, page A-1) for the single char- acter code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D.

  • Page 134: Image Scanner Report

    Image Scanner Report Scan the bar code below to generate a report for the connected image scan- ners. The report indicates the port, work group, image scanner name, and address. To assign a name to your image scanner, refer to "Menu Command Syntax"...

  • Page 135: Resetting The Standard Product Default Settings: All Application Work Groups

    Resetting the Standard Product Default Settings: All Application Work Groups The following bar code defaults all of the work groups to the factory settings. Standard Product Default Settings: All Application Groups Menu Commands starting on page 10-6 list the standard product default settings for each of the commands (indicated by an asterisk (*) on the program- ming pages).
  • Page 136 8 - 4...

  • Page 137: Chapter 9 - Visual Xpress

    Visual Xpress Visual Xpress Introduction Visual Xpress provides a wide range of PC-based programming functions that can be performed on an imager connected to your PC's COM port. Visual Xpress allows you to download upgrades to the imager's firmware, change pro- grammed parameters, and create and print programming bar codes.

  • Page 138: Installing Visual Xpress From The Web

    Installing Visual Xpress from the Web Note: Visual Xpress requires .NET software. If .NET is not installed on your PC, you will be prompted to install it during the Visual Xpress installation. 1. Access the Honeywell web site at www.honeywellaidc.com. 2. Click on Software Downloads.

  • Page 139: Chapter 10 - Serial Programming Commands

    Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will pro- gram the 2020. For complete descriptions and examples of each serial pro- gramming command, refer to the corresponding programming bar code in this manual.

  • Page 140: Query Commands

    Data The new value for a menu setting, identified by the Tag and Sub- Tag. Storage A single character that specifies the storage table to which the command is applied. An exclamation point (!) performs the com- mand’s operation on the device’s volatile menu configuration table. A period (.) performs the command’s operation on the device’s non-volatile menu configuration table.

  • Page 141: Responses

    Responses The device responds to serial commands with one of three responses: ACKIndicates a good command which has been processed. ENQIndicates an invalid Tag or SubTag command. NAKIndicates the command was good, but the Data field entry was out of the allowable range for this Tag and SubTag combination, e.g., an entry for a mini- mum message length of 100 when the field will only accept 2 characters.

  • Page 142: Trigger Commands

    Example #4: What are the device’s settings for all Codabar selections? Enter: cbr?. Response: CBRENA1[ACK], SSX0[ACK], CK20[ACK], CCT1[ACK], MIN2[ACK], MAX60[ACK], DFT[ACK]. This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on; the Start/Stop Character (SSX) is set to 0, or Don’t Transmit; the Check Character (CK2) is set to 0, or Not Required;...

  • Page 143: Resetting The Standard Product Default Settings: All Application Work Groups

    Menu Commands starting on page 10-6 list the factory default settings for each of the commands (indicated by an asterisk (*) on the programming pages). Note: Scanning this bar code also causes both the image scanner and the base to perform a reset and become unlinked. Refer to "Linking Image Scanner to Base"...

  • Page 144: Menu Commands

    Menu Commands Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Base Charge Mode *Automatic BASCHG1 Full Charge Rate BASCHG2 Low Charge Rate BASCHG3 Battery Charge Off BASCHG4 Image Scanner Modes Unlink Image Scanner BT_RMV - Single *Locked Link Mode BASCON0,DNG1 Open Link Mode...

  • Page 145: Terminal Interfaces

    Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Out-of-Range Alarm Base Alarm Duration 1-13 (Range 1 - 3000 sec BASORD (*0)) Image Scanner Alarm 1-13 BT_ORD Duration (Range 1 - 3000 sec (*0)) Alarm Sound Type Base Alarm Type 1-13 BASORW...
  • Page 146 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Program Keyboard *U.S.A. KBDCTY0 Country Belgium KBDCTY1 Brazil KBDCTY16 Canada (French) KBDCTY18 Czech Republic KBDCTY15 Denmark KBDCTY8 Finland (Sweden) KBDCTY2 France KBDCTY3 Germany/Austria KBDCTY4 Greece KBDCTY17 Hungary KBDCTY19 Israel (Hebrew) KBDCTY12...
  • Page 147 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Keyboard Style *Regular KBDSTY0 Caps Lock KBDSTY1 Shift Lock KBDSTY2 Automatic Caps Lock KBDSTY6 Emulate External KBDSTY5 Keyboard Keyboard Modifiers *Control + ASCII Off KBDCAS0 Control + ASCII On KBDCAS2 *Turbo Mode Off KBDTMD0...
  • Page 148 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Word Length: Data 7 Data, 1 Stop, Parity 2-10 232WRD3 Bits, Stop Bits, and Even Parity 7 Data, 1 Stop, Parity 2-10 232WRD0 None 7 Data, 1 Stop, Parity 2-10 232WRD6 7 Data, 2 Stop, Parity...

  • Page 149: Output Selections

    Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Wand Emulation Polar- *Black High 2-15 WNDPOL0 White High 2-15 WNDPOL1 Wand Emulation Idle Idle Low 2-15 WNDIDL0 *Idle High 2-15 WNDIDL1 Wand Emulation Data 2-16 WNDBLK0 Block Size 2-16 WNDBLK1...
  • Page 150 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Number of Beeps - BEPRPT1 Good Read Range 1 - 9 BEPRPT# Good Read Delay *No Delay DLYGRD0 Short Delay (500 ms) DLYGRD500 Medium Delay (1000 DLYGRD1000 Long Delay (1500 ms) DLYGRD1500 User-Specified Good...

  • Page 151: Prefix/Suffix Selections

    Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Centering Centering On DECWIN1 *Centering Off DECWIN0 Left of Centering Win- DECLFT### dow *40 Right of Centering Win- DECRGT### dow *60 Preferred Symbology PRFENA1 *Off PRFENA0 High Priority Symbol- PRFCOD## Low Priority Symbology PRFBLK##...

  • Page 152: Data Formatter Selections

    Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Suffix Add Suffix SUFBK2## Clear One Suffix SUFCL2 Clear All Suffixes SUFCA2 Function Code Trans- *Enable RMVFNC0 Disable RMVFNC1 Intercharacter Delay DLYCHR## User Specified Inter- Delay Length DLYCRX## character Delay Character to Trigger...
  • Page 153 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Codabar Start/Stop *Don’t Transmit CBRSSX0 Char. Transmit CBRSSX1 Codabar Check Char. *No Check Char. CBRCK20 Validate, But Don’t CBRCK21 Transmit Validate, and Transmit CBRCK22 Codabar Concatena- CBRCCT0 tion CBRCCT1 Require...
  • Page 154 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Interleaved 2 of 5 I25ENA0 I25ENA1 Interleaved 2 of 5 *No Check Char. I25CK20 6-10 Check Digit Validate, But Don’t I25CK21 6-10 Transmit Validate, and Transmit I25CK22 6-10 Interleaved 2 of 5 Mes- Minimum (2 - 80) *4...
  • Page 155 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Matrix 2 of 5 Message Minimum (1 - 80) *4 X25MIN## 6-14 Length Maximum (1 - 80) *80 X25MAX## 6-14 Code 11 Default All Code 11 C11DFT 6-14 Settings Code 11...
  • Page 156 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry UPC A Default All UPADFT 6-18 UPC A Settings UPC A UPAENA0 6-18 UPAENA1 6-18 UPC A Check Digit UPACKX0 6-18 UPACKX1 6-18 UPC A Number Sys- UPANSX0 6-19 UPANSX1...
  • Page 157 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry UPC E 5 Digit *Off UPEAD50 6-23 Addenda UPEAD51 6-23 UPC E Addenda *Not Required UPEARQ0 6-21 Required Required UPEARQ1 6-21 UPC E Addenda UPEADS0 6-22 Separator UPEADS1 6-22 EAN/JAN 13...
  • Page 158 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry EAN/JAN 8 5 Digit *Off EA8AD50 6-26 Addenda EA8AD51 6-26 EAN/JAN 8 Addenda *Not Required EA8ARQ0 6-26 Required Required EA8ARQ1 6-26 EAN/JAN 8 Addenda EA8ADS0 6-26 Separator EA8ADS1 6-26 Coupon Code...
  • Page 159 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry GS1 DataBar Default All GS1 Data- RSEDFT 6-30 Expanded Expanded Settings GS1 DataBar RSEENA0 6-30 Expanded RSEENA1 6-30 GS1 DataBar Minimum (4 - 74) *4 RSEMIN## 6-30 Expanded Msg.

  • Page 160: Minimizing Bluetooth/Ism Band Network Activity

    Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry PosiCode POSENA0 6-32 POSENA1 6-32 A and B On POSLIM0 6-33 A and B and Limited A POSLIM1 6-33 *A and B and Limited B POSLIM2 6-33 PosiCode Msg.
  • Page 161 Serial Setting Command Selection Page * Indicates default # Indicates a numeric entry Maximum Link *0 (0 - 100) BT_MLA### Attempts Relink Time-Out *3 (1 - 100) BT_RLT### 10 - 23...
  • Page 162 10 - 24...

  • Page 163: Chapter 11 - Product Specifications

    Product Specifications 3820 Product Specifications Parameter Specification Dimensions (Typical): Height 6.2 inches (15.7 cm) Length 5.3 inches (13.5 cm) Width 3.2 inches (8.1 cm) Weight (with battery) 9.2 ounces (260 g) Light Source 630 nM visible red LED Scan Rate 270 scans per second in most usages ±65 degrees Skew Angle...

  • Page 164: 3820I Product Specifications

    3820i Product Specifications Parameter Specification Dimensions (Typical): Height 6.5 inches (16.5 cm) Length 5.3 inches (13.5 cm) Width 3.2 inches (8.1 cm) Weight (with battery) 9.6 ounces (272 g) Light Source 630 nM visible red LED Scan Rate 270 scans per second in most usages ±65 degrees Skew Angle ±65 degrees...

  • Page 165: 2020-5Be Product Specifications

    2020-5BE Product Specifications Parameter Specification Dimensions (Typical): Height 3.1 inches (7.9 cm) Length 5.6 inches (14.2 cm) Width 4.3 inches (10.9 cm) Weight 8.8 ounces (250 g) Voltage: DC Barrel 8.5 to 9.5 volts Host Port 4.7-12 volts Current Draw: Base Only Base/Scanner w/ max charging 5 Volt Host...

  • Page 166: 2020-Cbe Product Specifications

    2020-CBE Product Specifications Parameter Specification Dimensions (Typical): Height 3.1 inches (7.9 cm) Length 5.6 inches (14.2 cm) Width 4.3 inches (10.9 cm) Weight 8.8 ounces (250 g) Voltage: DC Barrel 8.5 to 9.5 volts Current Draw: Base Only Base/Scanner w/ max charging 9 Volt DC Barrel 850mA Charge Rate to Scanner Battery...
  • Page 167 Standard Cable Pinouts Keyboard Wedge 11 - 5...
  • Page 168 Standard Cable Pinouts Wand Emulation 11 - 6...
  • Page 169 Standard Cable Pinouts Serial Output 11 - 7...
  • Page 170 Standard Cable Pinouts 11 - 8...

  • Page 171: Chapter 12 - Maintenance

    Maintenance Maintenance Repairs and/or upgrades are not to be performed on this product. These ser- vices are to be performed only by an authorized service center. "Customer Support" on page 13-1 for further information. Cleaning the Device Reading performance may degrade if the image scanner’s window is not clean. If the window is visibly dirty, or if the image scanner isn’t operating well, clean the window with a soft cloth or lens tissue dampened with water (or a mild soapy water solution).

  • Page 172: Replacing The 2020 Interface Cable

    Replacing the 2020 Interface Cable: 1. Turn the power to the host system OFF. 2. Disconnect the base’s cable from the terminal or computer. 3. Turn the base upside down. 4. Pull the connector out while maintaining pressure on the connector release clip.
  • Page 173 • The power cable is connected properly and there is power at the power source. • The host system power is on (if external power isn’t used). Is the green LED on? If the green LED isn’t illuminated, check that: •...
  • Page 174 The image scanner won’t read your bar code at all. 1. Scan the sample bar codes in the back of this manual. If the image scanner reads the sample bar codes, check that your bar code is readable. Verify that your bar code symbology is enabled (see Chapter 2.

  • Page 175: Chapter 13 - Customer Support

    For our latest contact information, please check our website at the link above. Product Service and Repair Honeywell International Inc. provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, con- tact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product.

  • Page 176: Online Product Service And Repair Assistance

    Honeywell’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any Honeywell product which is (i) improperly installed or used; (ii) damaged by accident or negligence, including failure to fol- low the proper maintenance, service, and cleaning schedule;...
  • Page 177 Honeywell or its authorized representatives. This warranty shall extend from the time of shipment for the duration published by Honeywell for the product at the time of purchase ("Warranty Period"). Any defective product must be returned (at purchaser’s expense) during the War- ranty Period to Honeywell’s factory or authorized service center for inspection.
  • Page 178 13 - 4...

  • Page 179: Appendix A - Reference Charts

    Reference Charts Symbology Chart Possible AIM Code ID Symbology AIM ID ID Modifiers (hex) ( m ) All Symbologies (0x99) China Post Q (0x51) Codabar a (0x61) Codablock F 0, 1, 4, 5, 6 q (0x71) Code 11 h (0x68) Code 128 0, 1, 2, 4 j (0x6A)
  • Page 180 Possible AIM Code ID Symbology AIM ID ID Modifiers (hex) ( m ) UPC-A c (0x63) UPC-A with Add-On c (0x63) UPC-A with Extended Coupon Code c (0x63) UPC-E E (0x45) UPC-E with Add-On E (0x45) UPC-E1 (obsolete) E (0x45) Note: “m”...
  • Page 181 ASCII Conversion Chart (Code Page 1252 Note: This table applies to U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings. Non-Printable Characters DEC HEX Character (Code) DEC HEX Character (Code) NULL DATA LINK ESCAPE (DLE) START OF HEADING DEVICE CONTROL 1 (DC1) (SOH)
  • Page 182 Printable Characters (Continued) DEC HEX Character DEC HEX Character DEC HEX Character < > <DEL> Extended ASCII Characters DEC HEX Character DEC HEX Character DEC HEX Character € € « Ö ¬ × ‚ Ø ƒ ® Ù „ ¯ Ú...

  • Page 183: Code Page Mapping Of Printed Bar Codes

    Extended ASCII Characters (Continued) DEC HEX Character DEC HEX Character DEC HEX Character Œ · â ¸ ã Ž ¹ ä º å » æ ‘ ¼ ç ’ ½ è “ ¾ é ” ¿ ê • À ë –...
  • Page 184 one the host program is expecting. If this is the case, select the code page with which the bar codes were created. The data characters should then appear properly. Note: The Code Page option is available for Code 39, Code 93, and Code 128. Code Page Standard Description...

  • Page 185: Appendix B - Minimizing Bluetooth/Ism Band Network Activity

    Minimizing Bluetooth/ISM Band Network Activity The settings described below can help you customize the re-linking behavior of the cordless linear imaging system to obtain the best compromise between convenience and low interference. Note: ISM band refers to the 2.4 to 2.48 GHz frequency band used by wireless networks, cordless phones, and Bluetooth.

  • Page 186: Maximum Link Attempts

    Event Auto Reconnect On Auto Reconnect Off Image scanner Re-link occurs automatically. reset due to firmware upgrade Image scanner Re-link occurs automatically. reset due to battery change Image scanner Re-link to new base occurs automatically. placed in different base unit Maximum Link Attempts The Maximum Link Attempts setting controls the number of times the image scanner tries to form a connection with a base unit or PC.

  • Page 187: Bluetooth/Ism Network Activity Examples

    Scan the Relink Time-Out bar code, then scan the number of seconds for the setting (from 1-100) from the inside back cover. Scan Save to save the setting. Default = 3 seconds. Relink Time-Out Bluetooth/ISM Network Activity Examples Default values: When the image scanner goes out of range, the image scanner repeatedly attempts to connect to base unit.
  • Page 188 Auto Reconnect Mode set to 1 Maximum Link Attempts set to 0 Relink Time-Out set to 10 Image Scanner Power Time-Out Timer set to 1800: Note: See Image Scanner Power Time-Out Timer on page 3-4. The image scanner attempts to connect to the base unit every 15 seconds, measured from start of attempt to start of attempt.

  • Page 189: Sample Symbols

    Sample Symbols UPC A 0 123456 7890 Interleaved 2 of 5 1234567890 Code 128 Code 128 EAN 13 9 780330 290951 EAN 8 3210 5 UPC-E 456123...
  • Page 190 Sample Symbols Code 39 Codabar BC321 Code 93 A13579B Straight 2 of 5 Industrial 123456-9$ Matrix 2 of 5 123456 6543210 GS1 DataBar (01)00123456789012...

  • Page 191: Programming Chart

    Programming Chart Discard Save Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save.
  • Page 192 Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com 3820-UG Rev E 11/11...

This manual is also suitable for:

2020-5b202038203820i

Table of Contents

Save PDF