Advertisement
GENERAL INFORMATION
The ADEMCO 6460S (silver) and 6460W (white) are
addressable Remote Keypads designed for use with
Honeywell's ADEMCO series control panels. Addresses are
set via the keypad keys.
The keys on the keypad are continuously backlit for
convenience.
NOTE: If supported, the ADEMCO 6460S and 6460W
keypads are supervised by control panel. Supervision must
be enabled for commercial fire installations.
KEYPAD DISPLAYS AND LEDS
The ADEMCO 6460S and 6460W keypads have the
following display features:
• 2-line Alpha Display
• Custom Zone Descriptors
• Built-in Speaker Sounder
• Dedicated Function Keys
• Backlit Display (permanent display backlighting is
an option on some controls; see the control's
instructions for details).
The following table shows the LEDs and their functions:
LED
Red
Lights when the system is armed in any mode
Green
Lights when the system is "ready" to be armed.
SPECIAL FUNCTION KEYS
The keypads also feature function keys. These keys may be
programmed for panic alarms or other special functions
such as macros. See the control's instructions for details.
Function keys must be held down for at least 2
seconds to activate an alarm; key pairs are activated
immediately.
Function Keys
A or [1] and [✻]
B or [✻] and [#]
C or [3] and [#]
D
INSTALLATION AND SETUP GUIDE
Function
WWW.DIYALARMFORUM.COM
WWW.DIYALARMFORUM.COM
ADEMCO
ADEMCO 6460S
ADEMCO
ADEMCO
WIRING AND INSTALLATION
The keypads can be surface mounted directly to a drywall,
or to a single- or double-gang electrical box.
1. Push the two case release snaps at the bottom of the
keypad with the blade of a medium screwdriver (this will
push in the release snap), then pull that side of the case
back away. Refer to Figure 1 for location of the case back
release snaps.
2. Route wiring from the control panel through the opening
in the case back.
3. Mount the case back to a wall or electrical box.
4. Wire directly from the keypad's terminal block to the
terminal block on the control panel. (See Wiring Table
below).
NOTE: No more than one wire per terminal may be
connected. If daisy-chained configuration is required,
pig-tail wires together so that only one wire is
terminated under the screw. Use 16-24 AWG wire only!
Wiring Table
Keypad
Control Panel
G
Data In
L
–
– Aux Pwr (GND)
+
+ Aux. Pwr
Y
Data Out
M
See the control panel's Installation and Setup Guide for
more complete details.
5. Reattach the keypad to its case back.
A
B
C
1
2
3
D
EF
ARMED
ABC
OFF
AWAY
STAY
READY
4
6
5
GH
M
NO
I
JKL
BYPA SS
MA X
TEST
7
8
9
X Z Y
PQ
RS
TUV
W
IN S
CH I ME
TAN
T
CODE
*
0
#
N
UM
EN
D
R EAD Y
NOTE:
TO REMOVE CASE BACK
PUSH IN THE TWO RELEASE
SNAPS LOCATED ALONG THE
BOTTOM OF THE KEYPAD
AND LIFT UP.
RELEASE
SNAPS
Figure 1. Removing the Case Back
800-03612 1/09 Rev. B
6460S/6460W
6460S
6460S
/6460W
/6460W
/6460W
REMOTE KEYPAD
REMOTE KEYPAD
REMOTE KEYPAD
REMOTE KEYPAD
Wire Color
Green
Black
Red
Yellow
D
6460S-001-V1
Advertisement
Related Manuals for Honeywell Ademco 6460S
Summary of Contents for Honeywell Ademco 6460S
- Page 1 INSTALLATION AND SETUP GUIDE GENERAL INFORMATION WIRING AND INSTALLATION The ADEMCO 6460S (silver) and 6460W (white) are The keypads can be surface mounted directly to a drywall, addressable Remote Keypads designed for use with or to a single- or double-gang electrical box.
-
Page 2: Setting & Viewing Keypad Address
REFER TO INSTALLATION INSTRUCTIONS FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE ALARM SYSTEM. 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 Copyright 2009 Honeywell International Inc. www.security.honeywell.com Ê800-03612rŠ 800-03612 1/09 Rev. B WWW.DIYALARMFORUM.COM WWW.DIYALARMFORUM.COM...