HP 4400 Replacement Instructions
Fibre channel and sas disk drive
Hide thumbs
Also See for 4400:
- Software manual (77 pages) ,
- Release note (48 pages) ,
- Quickspecs (31 pages)
Advertisement
Quick Links
HP Disk Drive Replacement
Instructions
These instructions apply to Fibre Channel and SAS
disk drives.
© Copyright 2011 Hewlett-Packard Development Company, L.P.
First edition: May 2011
The information in this document is subject to change without notice.
Printed in Puerto Rico
www.hp.com
*652989-001*
About this document
For the latest documentation, go to
manuals, and select your product.
The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the
express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional
warranty. HP shall not be liable for technical or editorial errors or
omissions contained herein.
WARRANTY STATEMENT: To obtain a copy of the warranty for this
product, see the warranty information website:
http://www.hp.com/go/storagewarranty
Before you begin
Observe the following precautions when replacing the disk:
Ensure you have a replacement part available before removing the
failed component. Removing a component impacts cooling within
the enclosure. Use a drive blank if a new drive is not available.
HP recommends that the replacement drive matches the capacity and
speed of the original drive. For example, if the original drive was a
300 GB, 15K RPM drive, the replacement would be a 300 GB, 15K
RPM drive.
Do not remove more than one disk at a time from the enclosure.
Doing so would impact cooling of the enclosure and may cause data
loss.
Parts can be damaged by electrostatic discharge. Use proper anti-
static protection.
Have a copy of the product user guide available for reference. You
can download a copy of the user guide from the product support
page on the HP website.
Figure 1
shows the numbering of Fibre Channel disk drives in the disk
enclosure used with the EVA.
Figure 1 FC disk drive numbering
.
Figure 2
shows the numbering of SAS small form factor (SFF) disk drives
and
Figure 3
shows the numbering of large form factor (LFF) disk drives
in the disk enclosure used with the P6300/P6500 EVA.
Figure 2 SAS SFF disk drive numbering
.
Page 1
http://www.hp.com/support/
Advertisement
Related Manuals for HP 4400
Summary of Contents for HP 4400
-
Page 1: About This Document
Parts can be damaged by electrostatic discharge. Use proper anti- static protection. © Copyright 2011 Hewlett-Packard Development Company, L.P. Have a copy of the product user guide available for reference. You First edition: May 2011 can download a copy of the user guide from the product support page on the HP website. -
Page 2: Types Of Disk Failures
If the system is redundant, continue with Verifying component failure. If the system is not redundant, information is displayed indicating the cause of the lack of redundancy. See the HP P6000 Command View online help to interpret the information that is displayed. In this situation, work with your HP call center agent to determine how to proceed. - Page 3 Check the disk Node World Wide Name against the error message UUID information recorded earlier to ensure you have selected the correct disk (Figure 1. Locate/Fault 2. Status Figure 6 FC disk status indicators Figure 8 Checking Node World Wide Name Check the disk operational state.
-
Page 4: Removing A Disk Drive
For an impending failure, you must ungroup the disk before you remove it: Removing a disk drive Determine the status of the disk drive from the hot-plug disk drive NOTE: LEDs. You should only ungroup one disk at a time. Before you ungroup a disk, verify that leveling is not in Back up all data on the disk drive. -
Page 5: Installing A Disk Drive
the firmware version against the supported disk firmware in the HP P6000 Enterprise Virtual Array Disk Drive Firmware Support Installing a disk drive document, which is available at the following website: http://www.hp.com/support/manuals Insert the disk drive into the drive bay (1, Figure 12) until it clicks, Click Disk Storage Systems under Storage, and then select the...