Honeywell HJK7000 Installation And User Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Keyboard
  5. HJK7000
  6. Installation and user manual

Honeywell HJK7000 Installation And User Manual

Ultrakey plus keyboard controller for videoblox and maxpro-net matrix systems
Hide thumbs
Table of Contents

Advertisement

Quick Links

UltraKey Plus
Keyboard Controller for VideoBloX
and MAXPRO-Net Matrix Systems
Model: HJK7000
Installation and User Guide
Document 800-02573 – Rev B – 11/2009

Advertisement

Table of Contents
loading

Related Manuals for Honeywell HJK7000

Summary of Contents for Honeywell HJK7000

  • Page 1 UltraKey Plus Keyboard Controller for VideoBloX and MAXPRO-Net Matrix Systems Model: HJK7000 Installation and User Guide Document 800-02573 – Rev B – 11/2009...
  • Page 3 Installation and User Guide...
  • Page 4 Revisions Issue Date Revisions 03/2009 New document. 11/2009 Updates throughout...
  • Page 5 Explanation of Symbols WARNING! The exclamation point in a red octagon is a WARNING. Failure to take or avoid a specific action could result in physical harm to a person or irreparable damage to equipment. Caution The lightning flash with arrowhead symbol within an equilateral triangle alerts the user to the presence of uninsulated dangerous voltage within the enclosure of the product that may be of sufficient magnitude to constitute a risk of electric shock to the person...
  • Page 6 CAUTION: Users of the product are responsible for checking and complying with all federal, state, and local laws and statues concerning the monitoring and recording of video and audio signals. Honeywell video systems shall not be held responsible for the use of this product in violation of current laws and statutes.

  • Page 7: Important Safety Instructions

    Warnings and Cautions Read the following cautions and warnings prior to installation and use of this product. Installation and servicing must be performed by qualified personnel in accordance with local codes and regulations. Consider using a UPS source to ensure satisfactory performance. Using replacement parts or accessories other than the original manufacturers may invalidate the warranty.
  • Page 8 In the event you have a problem with any Honeywell product, call Customer Service for assistance or to request a Return Merchandise Authorization (RMA) number. Be sure to have the model number, serial number, and the nature of the problem available for the technical service representative.

  • Page 9: Table Of Contents

    UltraKey Plus Controller Installation and User Guide Contents About this Document and the UltraKey Plus ......15 Document Overview .
  • Page 10 Contents Step 4: Configure the Controller for MAXPRO Mode..... . . 47 Installing and Configuring an Ethernet Connection ......48 Step 1: Connect to the UltraKey Plus Ethernet Port .
  • Page 11 UltraKey Plus Controller Installation and User Guide Figures Figure 0-1 UltraKey Plus Port Connections ....... . 19 Figure 1-1 UltraKey Plus Controller Keyboard Layout .
  • Page 12 Figures...
  • Page 13 UltraKey Plus Controller Installation and User Guide Tables Table 0-1 UltraKey Plus Specifications ........17 Table 0-2 Shipping Checklist .
  • Page 14 Tables...

  • Page 15: About This Document And The Ultrakey Plus

    Shipping Checklist, page 18 • UltraKey Plus Port Connections and Descriptions, page 19 The UltraKey Plus (HJK7000) is a replacement for the Honeywell Ultrakey (HEGSA002) controller and is compatible with Honeywell VideoBloX and MAXPRO-Net Video Matrix Systems. The UltraKey Plus has these modes available, depending on the installation: •...

  • Page 16: Finding More Information

    About this Document and the UltraKey Plus Finding More Information Refer to the online literature library to access other electronic documents in PDF format including data sheets, quick references, installation and user guides, specifications, software and product notices: http://www.honeywellvideo.com. Also see the back cover for international web sites and contact details.

  • Page 17: Ultrakey Plus Specifications

    UltraKey Plus Controller Installation and User Guide UltraKey Plus Specifications Table 0-1 UltraKey Plus Specifications Parameter Value Power Requirements 10.8 to 13.2 VDC @ 1 Ampere (A) or POE (48VDC, Class 3) Connector Types 1×Ethernet (10Base-T, 100Base-TX) RJ45 With LED 1×RS232/422/485 RJ45 With LED Type: TFT Backlight: LED...

  • Page 18: Shipping Checklist

    About this Document and the UltraKey Plus Shipping Checklist The following is included with your UltraKey Plus Controller shipment. Use of accessories is dependent on the type of installation. Ultrakey Plus can be connected to the matrix system either by serial port or Ethernet RJ45 connections. Table 0-2 Shipping Checklist Quantity...

  • Page 19: Ultrakey Plus Port Connections And Descriptions

    UltraKey Plus Controller Installation and User Guide UltraKey Plus Port Connections and Descriptions Figure 0-1 UltraKey Plus Port Connections DC Power Port Supports 12V (±10%) DC/1 A power input. Use the power adapter included with the shipment and insert one of the four adapters, based on your local power requirements. Document 800-02573 Rev B 11/2009...

  • Page 20: Ethernet Port

    About this Document and the UltraKey Plus Ethernet Port Note Ethernet is used to connect to the controller web browser, MAXPRO-Net or VideoBloX NetCPU. • 10/100M Ethernet PoE (power over Ethernet) input. If PoE is the power input, it is not recommended to connect this network with an outside building.

  • Page 21: Using The Ultrakey Plus Controller

    Using the UltraKey Plus Controller You may need to learn how to use the UltraKey Plus both before and after you begin configuring. Key availability is dependent on the mode selected. In this section: • Logging Onto the Controller, page •...

  • Page 22: Using The Ultrakey Plus To Navigate The Lcd Menus

    Using the UltraKey Plus Controller Using the UltraKey Plus to Navigate the LCD Menus There are a variety of ways to navigate both the LCD menus during configuration and set up as well as during normal operation with your matrix system. Figure 1-1 shows the layout of the UltraKey Plus and...

  • Page 23: Figure 1-2 The Ultrakey Navigation Controls

    UltraKey Plus Controller Installation and User Guide Figure 1-2 The UltraKey Navigation Controls Touch Pad and Ring Forward key (or up) Touch pad ring Right arrow key Left arrow key Touch pad - Use like a laptop Backward or reverse key mouse pad (or down) Touch Panel...

  • Page 24: Videoblox Key Functions

    Using the UltraKey Plus Controller VideoBloX Key Functions Note Figure 1-1 to locate each key as labeled in the ID column below. Table 1-1 VideoBloX Key Functions Key Description Function in Camera Mode PCK (Cam Mode) PCK (Device Mode) Alarm Acknowledge Alarms Alarm Ack Alarm Ack...
  • Page 25 UltraKey Plus Controller Installation and User Guide Table 1-1 VideoBloX Key Functions Key Description Function in Camera Mode PCK (Cam Mode) PCK (Device Mode) Touch wheel right Selects next camera Next Next Touch wheel left Selects previous camera Prev Prev Touch ring Up Nudges PTZ Up Touch ring Down...

  • Page 26: Maxpro Key Functions

    Using the UltraKey Plus Controller MAXPRO Key Functions Note Figure 1-1 to locate each key as labeled in the ID column below. Table 1-2 MAXPRO Key Functions Key Description Key Code Default MAX Function UltraKey Alarm Full Screen Alarm Ack None None Iris +...
  • Page 27 UltraKey Plus Controller Installation and User Guide Table 1-2 MAXPRO Key Functions Key Description Key Code Default MAX Function UltraKey Enter Enter Enter Clear Pause Monitor Monitor Monitor Camera Camera Camera PTZ Call PTZ Call PTZ Call Touch wheel right 105 (1-8) None None...
  • Page 28 Using the UltraKey Plus Controller...

  • Page 29: Installing Ultrakey Plus With Videoblox

    Installing UltraKey Plus with VideoBloX In this section: • Navigating the LCD Configuration Menus, page • Installing and Configuring a Serial Connection, page • Installing and Configuring an Ethernet Connection, page • (Optional) Configuring UltraKey Plus Using the Web Browser, page Note For all installations, refer to the applicable VideoBloX or VideoBloX Lite installation or user guides that came with your unit for more information.

  • Page 30: Navigating The Lcd Configuration Menus

    Installing UltraKey Plus with VideoBloX Navigating the LCD Configuration Menus Figure 2-1 LCD and LCD Navigation Keys Press key Numeric key pad and Ent key...

  • Page 31: Installing And Configuring A Serial Connection

    UltraKey Plus Controller Installation and User Guide Installing and Configuring a Serial Connection Step 1: Connect to the UltraKey Plus Using the Serial Port Note Use only COM1 when in VideoBloX mode. See Table 2-1 below. Table 2-1 Serial Port COM1 and COM2 Pin Assignments Serial Port Type Signal...

  • Page 32: Figure 2-2 Ac Power Adapter With Cee 7/16 Europlug

    Installing UltraKey Plus with VideoBloX Figure 2-2 AC Power Adapter with CEE 7/16 Europlug Slide plug onto the adapter and snap into place Figure 2-3 RJ45 to DB9 Male Adapter for VideoBloX and VideoBloX Lite CPUs Controller RJ45 to DB9 VideoBloX Serial Port male adapter...

  • Page 33: Step 2: Configure Port Settings

    UltraKey Plus Controller Installation and User Guide Figure 2-5 VideoBloX Serial Port RS422 Connection Example VB master: VideoBloX Serial Port (RS422) 1--RS422_TX – 2--RS422_TX + 3--RS422_RX + VIdeoBlox Master 4--RS422_RX – Connections 5--GND RJ45 to RJ45 to DB9 Male DB9 Male RJ45 define: PI NOUT 1--RS485_2+/RS422_2_TX+/...

  • Page 34: Step 3: Configure Address

    Installing UltraKey Plus with VideoBloX Note The default baud rate for VideoBloX is 19200 bps. It is recommended that you do not change this setting. Press DataBit to select 7 bit or 8 bit. 10. Press parity to select Even, Odd or None. 11.

  • Page 35: Installing And Configuring An Ethernet Connection

    UltraKey Plus Controller Installation and User Guide Installing and Configuring an Ethernet Connection For a list of accessories see Shipping Checklist on page and for port connections and pin assignments see UltraKey Plus Port Connections and Descriptions on page 19. The UltraKey Plus Controller runs TCP/IP keyboard protocol.

  • Page 36: Step 2: Set And Configure For An Ethernet Connection

    Installing UltraKey Plus with VideoBloX Figure 2-6 Ethernet Port Connections to VideoBloX Ethernet Port VideoBloX TCP/IP RJ45 network cables Controller 1 Network Controller 32 TCP/IP Ethernet Step 2: Set and Configure for an Ethernet Connection To set and configure for an Ethernet connection: Note No entry is required in the baud rate field for Ethernet connections.

  • Page 37: Step 3: Configure Address

    UltraKey Plus Controller Installation and User Guide Step 3: Configure Address To configure the keyboard address: Quit Press to exit from the Port Settings menu. Keyboard Address Press to select an address between 1 and 32 to assign to the controller.

  • Page 38: Step 1: Configure Ultrakey Plus To Videoblox Mode

    Installing UltraKey Plus with VideoBloX Figure 2-7 UltraKey Plus Login Page Step 1: Configure UltraKey Plus to VideoBloX Mode To configure UltraKey Plus to VideoBloX mode: Log onto the web browser. From the top menu, click the Configuration tab. See Figure 2-8.

  • Page 39: Step 2: Configure Videoblox Network Settings

    UltraKey Plus Controller Installation and User Guide Step 2: Configure VideoBloX Network Settings To configure VideoBloX network settings: From the side menu, click VideoBloX Configuration. See Figure 2-9. Under Keyboard ID Setting, enter a number between 1 and 32 to set the controller Under VB Device Network Setting, enter the IP address and Port Number of the VideoBloX system.

  • Page 40: Step 3B: Configure The Controller For An Ethernet Connection

    Installing UltraKey Plus with VideoBloX Figure 2-10 Port Settings Tab Step 3B: Configure the Controller for an Ethernet Connection To configure the controller for an Ethernet connection: From the side menu Settings:Hardware Config, click Port Settings. See Figure 2-11. In each of the fields, enter IP address, subnet mask, gateway and DNS values. Click Apply to save the configuration, Cancel to exit without saving, or Default to restore all factory default values.

  • Page 41: Installing Ultrakey Plus With Maxpro-Net

    Installing UltraKey Plus with MAXPRO-Net In this section: • Navigating the LCD Configuration Menus, page • Installing and Configuring a Serial Connection, page • Installing and Configuring an Ethernet Connection, page • (Optional) Configuring UltraKey Plus Using the Web Browser, page Note For all installations, refer to the applicable MAXPRO-Net installation or user guides for more information.

  • Page 42: Navigating The Lcd Configuration Menus

    Installing UltraKey Plus with MAXPRO-Net Navigating the LCD Configuration Menus Using the UltraKey Plus to Navigate the LCD Menus on page for detailed instructions to navigate or System Administration Using the Controller LCD on page for a configuration menu tree. Figure 3-1 LCD and LCD Navigation Keys Press key...

  • Page 43: Installing And Configuring A Serial Connection

    UltraKey Plus Controller Installation and User Guide Installing and Configuring a Serial Connection Step 1: Connect to the UltraKey Plus Using the Serial Port Note For a list of accessories, see Shipping Checklist on page 18. For port connections, see UltraKey Plus Port Connections and Descriptions page 19.

  • Page 44: Figure 3-2 Rs232 Serial Port Connections

    Installing UltraKey Plus with MAXPRO-Net Figure 3-2 RS232 Serial Port Connections Figure 3-3 RS232 Serial Port Connection and MegaPIT...

  • Page 45: Figure 3-4 Rs232 Serial Port Connection And Mx18

    UltraKey Plus Controller Installation and User Guide Figure 3-4 RS232 Serial Port Connection and MX18 RS232 Connections with an RJ45 to DB9 Female Adapter For RS232 connections with an RJ45 to DB9 female adapter: Select the applicable adapter plug and insert it into the AC adapter. Push to click it into place.

  • Page 46: Step 2: Configure Port Settings

    Installing UltraKey Plus with MAXPRO-Net Connect the RJ45 network cable to MAXPRO-Net: • For backwards compatibility with MAXPRO-Net CPUs, plug the RJ45 to DB9 female adapter included with your shipment into the applicable port of MAXPRO-Net. See Figure 3-6. Figure 3-6 RJ45 to DB9 Female Adapter (RS232) Controller RJ45 to DB9...

  • Page 47: Step 3: Configure Address And Joystick Speed

    UltraKey Plus Controller Installation and User Guide Press Port Settings and then either COM1 or COM2. The Serial Setting menu displays where you can see these settings - serial port mode, baud rate, databit, parity and stop bit. • Press Type to select RS422 or RS232. •...

  • Page 48: Installing And Configuring An Ethernet Connection

    Installing UltraKey Plus with MAXPRO-Net Installing and Configuring an Ethernet Connection Step 1: Connect to the UltraKey Plus Ethernet Port Table 3-2 RJ45 Ethernet Pin Assignments Port Signal RJ45 Ethernet TX + TX - To connect to the UltraKey Plus Ethernet port: Plug an RJ45 network cable from the network to the controller Ethernet port.

  • Page 49: Step 3: Configure Address And Joystick Speed

    UltraKey Plus Controller Installation and User Guide If the current mode is VB mode, change it to MAXPRO mode by pressing the Mode VB button and logging into the Setting menu again. Press Hardware Config. The current controller setting is displayed. Press Port Settings and then Ethernet.

  • Page 50: (Optional) Configuring Ultrakey Plus Using The Web Browser

    Installing UltraKey Plus with MAXPRO-Net (Optional) Configuring UltraKey Plus Using the Web Browser Logging onto the Web Browser If you have not already done so, navigate to, or copy and paste, the applicable IP address into your web browser: • LAN connections: for example, the default IP is http://192.168.1.9.

  • Page 51: Step 2: Configure Maxpro Network Settings

    UltraKey Plus Controller Installation and User Guide Figure 3-10 System Configuration Tab Step 2: Configure MAXPRO Network Settings To configure MAXPRO network settings: From the side menu, click MAXPRO Configuration. See Figure 3-11. Under Keyboard ID Setting, enter a number between 1 and 99 to set the controller ID.

  • Page 52: Step 3A: Configure The Controller For A Serial Port Connection

    Installing UltraKey Plus with MAXPRO-Net Figure 3-11 MAXPRO Configuration Tab Step 3A: Configure the Controller for a Serial Port Connection To configure the controller for a serial port connection: From the side menu Settings:Hardware Config, click Port Settings. See Figure 3-12.

  • Page 53: Step 3B: Configure The Controller For An Ethernet Connection

    UltraKey Plus Controller Installation and User Guide Figure 3-12 Port Settings Tab Step 3B: Configure the Controller for an Ethernet Connection To configure the controller for an ethernet connection: From the side menu Settings:Hardware Config, click Port Settings. See Figure 3-13.
  • Page 54 Installing UltraKey Plus with MAXPRO-Net...

  • Page 55: System Administration And Troubleshooting

    System Administration and Troubleshooting In this section: • System Administration Using the Controller LCD, page • System Administration Using the Web Browser, page System Administration Using the Controller LCD Logging on and Navigating to the Settings Menu If you have not already done so, install and connect the controller to a power source.

  • Page 56: Configuring The Hardware

    System Administration and Troubleshooting Configuring the Hardware Log onto the controller. From the Settings menu, press Hardware Config. The Hardware Config submenu displays. Firmware Update To update firmware, press Slider FM Update. It may takes several minutes to update slider firmware. Keyboard Address To modify/change the keyboard address, press Keyboard...
  • Page 57 UltraKey Plus Controller Installation and User Guide Port Settings To configure port settings, press Port Settings. • Serial Port Settngs (COM 1) Press COM1 to set type(RS422 or RS485), Baudrate, Databit, Parity and Stopbit. • Serial Port Settings (COM 2) Press COM2 to set type(RS232 or RS485), Baudrate, Databit, Parity and Stopbit.

  • Page 58: Managing The Users

    System Administration and Troubleshooting Joystick Res To adjust joystick speed, press Joystick Res to select low or high. Zero Joystick To reset the default position of the Joystick, Press Zero Joystick. Managing the Users Log onto the controller. From the Settings menu, press User Manage.

  • Page 59: Configuring Hardkeys

    UltraKey Plus Controller Installation and User Guide Deleting a User To delete a user ( for example, ABC) Click the user to be deleted. Press Delete. • Select OK to delete the user. • Select Cancel to cancel the operation. Changing Passwords To change the password of a user (for example, ABC):)
  • Page 60 System Administration and Troubleshooting Setting Properties To set hardkey properties: Press Set Properties. A message pops up and requires you to press a hardkey. Press a hardkey. Press Max Key to start operating or press Cancel to quit. The scroll menu shows all types of executive actions you can do.
  • Page 61 UltraKey Plus Controller Installation and User Guide Modifying a Menu From the hardkey configuration menu, you can modify the menus. For detailed information on how to modify a menu, see User Menus, page 62. Press Menu to edit the system menus. To edit the menu name: Select it in the scroll window, press Edit...

  • Page 62: Checking The Hardware

    System Administration and Troubleshooting Checking the Hardware To check the hardware: Log onto the controller. From the Settings menu, press Check Hardware. The Check Controls submenu displays. • Key: When you press a key, the key value and its status is displayed on LCD.

  • Page 63: Selecting The Language

    UltraKey Plus Controller Installation and User Guide Note To set the Maxkey and Menu in step 7 and 8, see Configuring Hardkeys, page for more detailed information. Press BG Color/Text Color to set the color of button/text. 10. To delete the button, press Delete Button.

  • Page 64: General Information

    System Administration and Troubleshooting General Information To view general information about the controller: Log onto the controller. From the Settings menu, press General Info. The controller’s general information displays. Press any place on the LCD to return to the previous menu.

  • Page 65: Configuring The Hardware

    UltraKey Plus Controller Installation and User Guide In the Password field enter 1234 (default). Click Login. Configuring the Hardware Log onto the web browser. From the side menu Settings:Hardware Config, click Basic Config. See 4-1. Select Background Light from the drop down list. Options are Off, Low, Middle or High.

  • Page 66: Configuring Hardkeys

    System Administration and Troubleshooting To change a user password: Select the user in the user list. In the Change Password section, enter the old password and the new password. Press Apply to save the operation or Cancel to quit editing. Figure 4-2 Manage Users Configuring Hardkeys...

  • Page 67: Configuring File

    UltraKey Plus Controller Installation and User Guide Figure 4-3 Configuring Hardkey Configuring File Log onto the web browser. From the side menu Settings, click Configuration File. See Figure 4-4 Right-click ConfigFile under the green arrow. Then select Save Target AS... to save the desired file.

  • Page 68: Upgrading The Ultrakey Plus Firmware

    System Administration and Troubleshooting Upgrading the UltraKey Plus Firmware Log onto the web browser. From the top menu, click the Upgrade tab. The warning message Please make sure the network connection is connected during system upgrading displays. See Figure 4-5. Click OK.

  • Page 69: Changing The Ultrakey Plus Password

    UltraKey Plus Controller Installation and User Guide Figure 4-6 System Reboot Changing the UltraKey Plus Password Log onto the web browser. In the upper right corner, click Change Password. See Figure 4-7. In the Old Password field, enter the current password. In the New Password field, enter a new password.
  • Page 70 System Administration and Troubleshooting...

  • Page 71: Index

    UltraKey Plus Controller Installation and User Guide Index controller configuring address, MAXPRO-Net 47, navigating menus configuring address, VideoBloX navigation keys, MAXPRO-Net configuring Ethernet connection, MAXPRO-Net navigation keys, VideoBloX configuring serial port connection, MAXPRO-Net configuring VideoBloX mode configuring with web browser configuring with web browser, MAXPRO-Net MAXPRO-Net configuring, MAXPRO mode 47,...
  • Page 72 configuring settings, MAXPRO-Net pin assignments, MAXPRO-Net configuring, MAXPRO-Net RS232/RS422/RS485, described DC power shipping checklist Ethernet configuring, VideoBloX specifications Ethernet to controller, MAXPRO-Net Ethernet, configuring with web browser, VideoBloX Ethernet, described USB port location RS232 serial port, MAXPRO-Net RS232/422/485, described serial, connecting, MAXPRO-Net VideoBloX serial, pin assignments, MAXPRO-Net configure Ethernet port...
  • Page 74 Document 800-02573 — Rev B — 11/2009 © 2009 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use thereof.

This manual is also suitable for:

Hz-7000 - sure-set digital heater fan

Table of Contents