Factory-set Voice List The following voices are preset at the factory. Each voice has different settings which you can change by moving the CONTROL knobs and other controllers. Each controller is assigned with its own unique settings. In general, AEG or FEG is assigned to knobs 1 and 2, VCF Cutoff to knob 5, Resonance to knob 6, and Effects-related parameters to knobs 7 and 8, respectively.
Page 3
Cat. Voice Name Description Acid 2 Acid sound number 2. Twiddle those knobs for ultimate experience. Acid 3 Harder acid sound. [RIBBON] controls distortion amount. Watch the resonance. Soft Brass Soft analog brass sound. Try the [RIBBON] controller. Hard Brass Bright &...
Page 4
Cat. Voice Name Description Polyswell Warm and wide poly synth sound with long filter attack. Padbells Combination of bells with pad. Use [RIBBON] to fade the bells in or out. DX E.Piano Bright FM electric piano sound. Condenser Condenser piano sound. WhitneyEP Electric piano with clean Whitney Houston sound.
3-BAND EQ Parameter Display Ctrl Matrix Low Freq 32Hz~2.0kHz Low Gain -12~+12dB Mid Freq 100Hz~10.0kHz Mid Gain -12~+12dB Mid Reso 1.0~12.0 High Freq 500Hz~16.0kHz High Gain -12~+12dB DELAY EFFECT DELAY L,C,R Parameter Display Ctrl Matrix Lch Dly 0.1~660.0ms Rch Dly 0.1~660.0ms Cch Dly 0.1~660.0ms...
Page 8
Effect Parameter Tables Table#1 LFO Frequency Data Value Data Value Data Value 5.39 20.85 0.08 5.47 21.52 0.17 5.56 22.2 0.25 5.64 22.87 0.34 5.72 23.54 0.42 5.81 24.21 0.51 5.89 24.89 0.59 5.98 25.56 0.67 6.06 26.23 0.76 6.15 26.9 0.84 6.23...
Page 9
Common Control Matrix Parameter Name Ctrl Matrix : Param Group Param Name Data Value ComnVolume Comn Pan Vari Param Dly Return Rev Return Control Change Modes MODE1 MODE2 MODULATION MODULATION SCENE SELECT FOOT CONTROLLER FOOT CONTROLLER PORTAMENTO TIME PORTAMENTO TIME DATA ENTRY MSB DATA ENTRY MSB MAIN VOLUME...
Page 10
Control Matrix List And Free EG Track Parameter List Parameter Name Ctrl Matrix : Param Ctrl Matrix : Calc Group Param Name Data Value Multiply or Add *1 Scene Tune Pitch Up Pitch Down PEG Decay PEG Depth PEG Sw Port Time LFO1 Wave LFO1 Speed...
Many MIDI messages listed in the MIDI Data Format section are expressed in hexadecimal or binary numbers. Hexadecimal numbers may include the letter “H” as a suffix. The letter “n” indicates a certain whole number. The chart below lists the corresponding decimal number for each hexadecimal/binary number. Decimal Hexadecimal Binary...
*2 Used only when assigning the parameter with RPN numbers. In addition, the following CONTROL NUMBERs will be transmitted/received when Control Change Mode 2 is selected. (These are unique to the AN1x and therefore not in accordance with the MIDI 1.0 standard.) c = 3...
+-----------------------+ The tone generator will respond to both note data received via MIDI and the data generated by the AN1x such as note data and control data. ALL SOUNDS OFF clears all the sounds in the specific channel played by both the keyboard and the data via MIDI.
Current Voice Scene Ctrl Buffer CURRENT PATTERN Current Pattern Buffer USER VOICE User Voice 1 (only Bulk Dump) User Voice 128 (only Bulk Dump) MIDI Data Table <1-2> MIDI Parameter Change Table (System) Address Size Data Prameter Name Description (H) (H) 00 00 00 0AA...356 Master tune -100.0(0AA)...+100.0 cent(356)