Toro ReelMaster 01005 Operator's Manual
5, 7, and 11-blade reel mower
Hide thumbs
Also See for ReelMaster 01005:
- Operator's manual (21 pages) ,
- Operator's manual (20 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Toro ReelMaster 01005
Summary of Contents for Toro ReelMaster 01005
- Page 1 Form No. 3387-429 Rev A Reelmaster ® 5, 7, and 11-Blade Reel Mower Model No. 01005—Serial No. 240000001 and Up Model No. 01007—Serial No. 240000001 and Up Model No. 01011—Serial No. 240000001 and Up *3387-429* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Fasteners ............5 5 Parallel the Bedknife to the Reel ......6 You may contact Toro directly at www.Toro.com for product 6 Setting the Height Of Cut........7 and accessory information, help finding a dealer, or to register Product Overview ............ -
Page 3: Safety
Toro replacement parts and accessories replace it before operation is commenced. Also tighten to keep the Toro all Toro. Never use "will-fit" any loose nuts, bolts, and screws to ensure that the cutting replacement parts and accessories made by other unit is in safe operating condition. -
Page 4: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Remove the mower from the carton Check the wheel hubs and install the – No parts required wheels –... -
Page 5: Checking The Gear Case Oil
Checking the Gear Case Oil No Parts Required Procedure 1. Position the mower on a level surface. 2. Raise and block the back of the mower until there is g026924 approximately 0.260 m (10–1/4 inches) between the Figure 2 bottom of the gear case extending behind the roller bracket and the level surface (Figure 4). -
Page 6: Checking The Reel Bearings And Mower
Checking the Reel Bearings and Mower Fasteners No Parts Required Procedure g026927 Figure 5 1. Rotate the center adjusting knob until the bedknife does not contact the reel. Try to spin the reel. If the 1. Throwout knobs 2. Bedknife adjusting knob reel does not spin, adjust the reel bearings;... -
Page 7: Setting The Height Of Cut
in the paper being cut or a slight drag when the paper 4. To make a finer adjustment to the cutting height or is pulled. to adjust the roller, the adjusting nut may be moved 1/2 notch or 1.19 mm (3/64 of an inch) by using the 9. -
Page 8: Product Overview
Product Overview Operation Note: Determine the left and right sides of the machine Specifications from the normal operating position. Weigh 114 kg (252 lb) 11 Blade Adjusting the Bedknife to the 112 kg (248 lb) 7 Blade 110 kg (243 lb) 5 Blade Reel for Light Contact (All with 0.406 m (16 inch) -
Page 9: Operating Tips
6. At the beginning of the cutting day, when the reels pressure must be maintained at 241.3 kpa (35 psi). Low are cold, engage the reel throwout knobs (Figure 8). tire pressure can cause bedknife to dip into the grass Operate the mowers for 15 to 20 minutes so the and scalp the turf. - Page 10 g026932 Figure 10 1. Nicked reel blades 2. Noise – A mower that has sharp cutting edges and is adjusted with light contact will emit a desirable whispering sound when the reel is spinning. By contrast, buzzing, clicking, or metallic sounds during operation indicate that the mower is probably being operated with heavy contact between the bedknife and the reel.
-
Page 11: Maintenance
1/4 turn to preload the bearing. 6. Reinstall the inspection cover and the wheel.. Grinding Note: For detailed sharpening information, refer to the Toro Manual for Sharpening Reel and Rotary Mowers, Form No. 09168SL. New and old bedknives should be ground attached to the bedbar;... -
Page 12: Lapping
g026937 Figure 15 1. Reel pinion cover 4. Disengage the reel. g026936 5. Connect the lapping machine coupler to the nut on Figure 14 the end of the reel shaft. 1. Bed knife 3. 15 - 20 degrees relief When lapping, use a good grade of commercial lapping angle compound. -
Page 13: Adjusting The Reel, Roller And Wheel Bearing
2. True the bedknife attached to the bedbar by grinding. Slide the roller shaft into the roller until it penetrates Refer to the Toro Manual for Sharpening Reel and the inner most oil seal on the right–hand side. Rotary Mowers, Form No. 09168SL 6. - Page 14 Notes:...
- Page 15 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.