Advertisement
Quick Links
Reverse 4WD Kit
LT-F3000 Triple Flail, LT3340 Triple Reel, or LT2240 Compact Triple
Turf Mower
Model No. 02858—Serial No. 400000000 and Up
This kit provides improved traction in reverse when traction is reduced in certain ground conditions.
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Description
No parts required
High-pressure valve
Coil
Nut
Adapter fitting (1/4 x 7/16 inch)—Model
31654, and Models 31657 and 31659 with the
optional differential-lock kit.
Seal (1/4)—Models 31657 and 31659 with the
optional differential-lock kit.
Quick-connect fitting—Model 31654, and
Models 31657 and 31659 without the optional
differential-lock kit.
Dust cap—machines without the optional road
light kit.
Reducer fitting (3/4 x 7/16 inch)—Models
31657 and 31659 without the optional
differential-lock kit.
Hydraulic test equipment 260 to 325 bar (3771
to 4714 psi), with a quick-disconnect fitting
(facility provided)
Hydraulic test equipment 260 to 325 bar (3771
to 4714 psi) with a Quick-Connect Fitting
(machines without the optional differential-lock
kit) or a Minimess™ fitting (machines with the
optional differential-lock kit)—facility provided
No parts required
No parts required
No parts required
No parts required
No parts required
© 2020—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Qty.
–
Prepare the machine.
2
2
Install the rear traction-manifold solenoids.
2
1
1
1
Install the pressure test fitting.
1
1
.
Prepare to test hydraulic pressure.
.
Prepare to test hydraulic pressure.
Connect the battery and installing the storage
–
compartment.
–
Test the hydraulic pressure.
–
Finish the hydraulic test.
–
Finish the hydraulic test.
–
Check the hydraulic-fluid level.
Register at www.Toro.com.
Form No. 3443-350 Rev A
Installation Instructions
Use
*3443-350*
Original Instructions (EN)
Printed in the UK
All Rights Reserved
Advertisement
Related Manuals for Toro 02858
Summary of Contents for Toro 02858
- Page 1 Reverse 4WD Kit LT-F3000 Triple Flail, LT3340 Triple Reel, or LT2240 Compact Triple Turf Mower Model No. 02858—Serial No. 400000000 and Up Installation Instructions This kit provides improved traction in reverse when traction is reduced in certain ground conditions. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
- Page 2 Preparing to Install the Kit Remove the 3 knobs and 3 washers that secure the storage compartment to the machine, and remove the compartment (Figure Washing the Machine Important: Before installing this kit, you Disconnecting the Battery must thoroughly clean the machine to avoid Loosen the forward nut of the negative contaminating the hydraulic system—a clean battery-cable terminal...
- Page 3 Installing the Rear Traction-Manifold Solenoids At the back of the machine, remove the check valve from port-CV of the traction manifold (Figure g343945 g343931 Figure 5 3. Nut 1. Coil 2. High-pressure valve Torque the nut to 8 N∙m (6 ft-lb). Remove the cap from the 2-socket connector g343934 Figure 3...
- Page 4 Plug the 2-socket connector REVERSE SOLENOID into the 2-pin connector of the coil (Figure Repeat steps through at the other side of the rear traction manifold. Installing the Quick-Connect Test Fitting Machines without the Optional Road Light Kit or Differential-Lock Installing the Quick Connect Fitting Model 31654...
- Page 5 Torque the quick-connect fitting to 27 N∙m (20 ft-lb). Assemble the retainer of the dust cap onto the quick-connect fitting (Figure You will install the cap over the fitting in Installing the Dust Cap (page 11). Installing the Quick Connect Fitting Models 31657 and 31659 At the right side of the traction pump, remove the...
- Page 6 Assemble the retainer of the dust cap onto the quick-connect fitting (Figure 12). Note: You will install the cap over the fitting in Installing the Dust Cap (page 13). Preparing to Test the Hydraulic Pressure Model 31654 Installing the Quick-Connect g344291 Figure 14 Fitting...
- Page 7 Preparing to Test the Hydraulic Pressure Models 31657 and 31659 Installing the Quick-Connect Fitting Machines with the Optional Road Light Kit—and without the Optional Differential-Lock g344403 Figure 16 At the right side of the traction pump, remove the 3-pin connector labeled BRAKE PRESSURE Connect the battery, lower the hood, and perform from the brake-pressure transducer...
- Page 8 Compartment (page 9), and Testing the Hydraulic Pressure (page 10). Preparing the Traction Pump Machines with and without the Optional Road Light Kit—and without the Optional Differential-Lock Kit At the right side of the traction pump, assemble the test equipment onto the quick-connect fitting (Figure 22).
- Page 9 Preparing the Forward Traction Connect the battery, install the storage compartment, and perform the Manifold hydraulic-pressure test; refer to Testing the Machines with the Optional Differential-Lock Hydraulic Pressure (page 10). Unlatch and raise the operator’s platform; refer Connecting the Battery to the Operator’s Manual.
- Page 10 Important: If the hydraulic pressure measurements are lower than or higher than the normal pressure range, contact Toro customer care. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operator’s position.
-
Page 11: Brake Pressure Sensor
Note: Retain the quick-connect fitting. g344324 Figure 30 1. Brake-pressure 2. 3-pin connector (labeled transducer BRAKE PRESSURE SENSOR g344321 Figure 28 1. Adapter fitting 2. Quick-connect fitting Installing the Dust Cap Machines without the Optional Road Light Kit Assemble the brake-pressure transducer into the adapter fitting (Figure 29). - Page 12 Note: Retain the quick-connect fitting. g344071 Figure 34 g344317 Figure 32 1. Reducer fitting (3/4 x 7/16 2. Quick-connect fitting inch) Finishing the Hydraulic Assemble the brake-pressure transducer (Figure 35) into the reducer fitting (3/4 x 7/16 inch). Test Models 31657 and 31659 Installing the Brake-Pressure Transducer Machines with the Optional Road Light...
- Page 13 g344072 g344079 Figure 36 Figure 38 1. 3-pin connector (labeled 2. Brake-pressure transducer BRAKE PRESSURE SENSOR Installing the Dust Cap Machines with the Optional Differential-Lock Installing the Dust Cap Machines without the Optional Road Light Kit Raise the operator’s platform; refer to the or the Optional Differential-Lock Kit Operator’s Manual.
-
Page 14: Checking The Hydraulic-Fluid Level
g344122 Figure 40 1. Dust cap 2. Minimess fitting (port-TPB—front traction manifold) Lower and latch the operator’s platform; refer to the Operator’s Manual. Checking the Hydraulic-Fluid Level Check the hydraulic fluid level in the tank—add hydraulic fluid as needed; refer to Checking the Hydraulic Fluid in the Operator’s Manual for your machine. - Page 15 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.