Advertisement
Quick Links
Wall Hanging Bracket Set
OT-WH30 Installation Manual
The OT-WH30 is an optional hanging bracket for attaching the printer to a wall.
This manual describes the procedures and precautions for installing and using the
OT-WH30.
Precautions
This hanging bracket is for hanging a TM-m30, TM-m30II, or TM-m30II-H printer.
Depending on the printer model, the included screws to mount the bracket are
different as described below. Make sure to use the correct screws.
❏ TM-m30:
3x10 bracket mounting screw (Silver)
❏ TM-m30II, TM-m30II-H:
2.5x10 bracket mounting screw (Black)
If you use the screws for another printer model, or mix up the screws by mistake, the
bracket cannot be mounted properly or the printer may not work properly.
Unpacking
Make sure that you have all the items shown, and that none has been damaged. If
you find anything missing or damaged, contact your dealer.
□ Wall-mount
□ 3 × 10 Screws for bracket
□ 2.5 × 10 Screws for bracket
(Silver, 2 pieces)
(Black, 2 pieces)
For TM-m30
For TM-m30II/TM-m30II-H
□ Spacers (2 pieces)
□ Installation Manual
Note:
❏ Screws for wall-mount are not included. Please use screws appropriate to
the type of wall being used.
❏ Depending on the conditions during storage and shipping, some rust may
form around the edges of the wall-mount or bracket. This may be removed
with sandpaper.
Installation
Turn off the printer.
Attach the wall-mount to the wall.
CAUTION:
❏ To fix the printer securely, install the wall-mount on a wall made of
wood, concrete, or metal. The thickness of the wall should be 10 mm
or more.
❏ In order to insure that the wall-mount can properly support the
weight of the printer, please secure it with screws appropriate to
the type of wall the wall-mount is installed on. A screw with 4 mm
diameter and length of 12 mm or more is recommended.
❏ Be sure to fasten the wall-mount securely to the wall with a screw in
each of the 6 holes.
❏ Before attaching the wall-mount, make sure enough space remains
around the printer.
❏ Make sure that there is enough space for opening the roll paper
cover.
□ Bracket
Attach the bracket to the holes on the bottom cover using the included
screws.
CAUTION:
Make sure you tighten the screw completely when installing.
If they are not tightened completely, the mount or the printer could fall
or topple over causing injury or accident to occur.
84 mm
(3.31 inches)
26 mm
(1.02 inches)
26 mm
(1.02 inches)
Peel off the stickers from the spacers, and attach them to the printer in
the positions shown below.
CAUTION:
Make sure that the surface of the printer is clean and dry.
Slide the bracket into the slots of the wall-mount.
CAUTION:
When mounting the printer, make sure that the wall-mount is securely
fastened to the wall.
©Seiko Epson Corporation 2015-2020. All rights reserved.
Printed in XXXXXX/YYYYYYYYYYYY
Advertisement
Related Manuals for Epson OT-WH30
Summary of Contents for Epson OT-WH30
- Page 1 Wall Hanging Bracket Set OT-WH30 Installation Manual Installation The OT-WH30 is an optional hanging bracket for attaching the printer to a wall. This manual describes the procedures and precautions for installing and using the OT-WH30. Turn off the printer. Peel off the stickers from the spacers, and attach them to the printer in Precautions the positions shown below.
- Page 2 壁掛金具 OT-WH30 設置マニュアル 取り付け OT-WH30 はプリンターを壁に取り付けて使用するための取付金具です。 本マニュアルは OT-WH30 の取り付け方法、取り扱い上の注意点などについ て説明しています。 スペーサーの接着面のシールを剥がし、下図で示した位置に貼り付け プリンターの電源を切ります。 ます。 使用上の注意 壁に壁掛け金具を取り付けます。 本金具は TM-m30, TM-m30II, TM-m30II-H に使用できます。また、プリ 注意 : ンターによって使用できる同梱のネジは異なります。それぞれのプリンターに プリンターケースの接着面がきれいで乾いていることを確認してく 合った同梱のネジを使用してください。 注意 : ださい。 ❏ TM-m30： ❏ プリンターを確実に固定するために、木、コンクリート、また 3x10 ハンガー取り付けネジ（銀色） は金属の壁に壁掛け金具を取り付けてください。壁の厚さは 10mm 以上を推奨します。 ❏ TM-m30II, TM-m30II-H： ❏ 壁掛け金具の取り付けネジは、プリンターを保持するのに十分...