Related Manuals for Toro 58601
Summary of Contents for Toro 58601
- Page 1 Form No. 3441-764 Rev D 10in Cultivator Model No. 58601—Serial No. 321000001 and Up *3441-764* Register at www.Toro.com. Original Instructions (EN)
- Page 2 Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product.
-
Page 3: Table Of Contents
Contents Safety Safety ............... 3 This machine has been designed in accordance with General Safety ........... 3 ANSI B71.8-2016. Safety and Instructional Decals ......4 Setup ................ 5 General Safety 1 Assembling the Handle ........5 2 Rotating the Drag Stake........6 This product is capable of amputating hands and Product Overview ............. -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal144-4732 144-4732 1. Press the primer 3 times, push the choke lever down, pull the recoil-start handle, and once the engine is running pull the choke lever up. -
Page 5: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Knob nut Curved washer Saddle bolt Assemble the handle. Middle handlebar Upper left handlebar Upper right handlebar – No parts required Rotate the drag stake. Assembling the Handle Parts needed for this procedure: Knob nut... -
Page 6: Rotating The Drag Stake
Rotating the Drag Stake No Parts Required Procedure Remove the lock pin. Rotate the drag stake so that it points downward, facing toward the tines. Install the lock pin. g334212 Figure 4 1. Knob nut (2) 4. Left upper handle 2. -
Page 7: Product Overview
Product Overview g334228 Figure 6 1. Engine on/off switch 6. Engine 7. Fuel cap 2. Choke lever 3. Throttle control 8. Tines 4. Handlebar-height adjustment 9. Primer bulb 5. Starter handle 10. Wheel vertical guide Controls Choke Lever Move the choke lever on the engine to the C HOKE Engine On/Off Switch position when initially starting a cold engine, then... -
Page 8: Specifications
To ensure optimum performance and continued safety • Do not allow children or untrained adults to operate certification of the machine, use only genuine Toro or service the machine. Local regulations may replacement parts and accessories. Replacement restrict the age of the operator. -
Page 9: Adding Fuel
Adding Fuel • Do not overfill the fuel tank. Replace the fuel cap and tighten it securely after fueling. Clean up spilled fuel before starting the engine. Recommended Fuel • Do not fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. -
Page 10: Performing Daily Maintenance
Note: Do not mix fuel and oil in the fuel tank. Oil at room temperature mixes easier and more thoroughly than cold oil. Oil below 0°C (32°F) requires additional mixing. Using Stabilizer/Conditioner Use fuel stabilizer/conditioner in the machine to keep the fuel fresh longer when used as directed by the fuel-stabilizer manufacturer. -
Page 11: During Operation
• Wear appropriate clothing, including eye protection; long pants; substantial, slip-resistant footwear; hearing protection; and gloves. Tie back long hair and do not wear loose clothing or loose jewelry. • Keep your hands, feet, other body parts, and clothing away from rotating tines and moving parts of the machine. -
Page 12: Starting The Engine
Release the throttle lever. • Use only accessories and attachments approved Remain in the operating position and grab the by The Toro® Company. handle bar with 1 hand. • Do not change the engine governor settings or overspeed the engine. -
Page 13: Adjusting The Drag Stake
Operating Tips • Inspect the area where you will use the cultivator and remove all objects such as large rocks, trash, and branches before cultivating to prevent equipment damage. • The clutch transfers maximum power after about 2 hours of normal operation. During this break-in period, the clutch may slip. -
Page 14: After Operation
After Operation After Operation Safety General Safety • Shut off the machine and wait for all moving parts to stop before you leave the operator’s position. Disconnect the spark-plug wire, keep it away from the plug to prevent accidental starting, and allow the machine to cool before adjusting, fueling, unclogging, servicing, cleaning, or storing the machine. -
Page 15: Maintenance
• To ensure optimum performance of the machine, Maintenance Safety use only genuine Toro replacement parts and accessories. Replacement parts and accessories • Inspect the machine frequently to ensure that it made by other manufacturers could be dangerous, is in safe working condition and that shear bolts, and such use could void the product warranty. -
Page 16: Engine Maintenance
Engine Maintenance Servicing the Spark Plug Service Interval: Every 20 hours—Check, clean, and gap the spark plug. Servicing the Air Filter Yearly—Replace the spark plug. Service Interval: Before each use or daily—Check Ensure that the air gap between the center and side the air filter. -
Page 17: Storage
Checking the Spark Plug Storage Important: Do not clean the spark plug(s). Always replace the spark plug(s) when it has a Storage Safety black coating, worn electrodes, an oily film, or • cracks. Shut off the machine and wait for all moving parts to stop before you leave the operator’s position. - Page 18 Dispose of fuel properly. Recycle the fuel according to local codes. Important: Do not store fuel containing stabilizer/conditioner longer than the duration recommended by the fuel-stabilizer manufacturer. Remove and check the condition of the spark plug; refer to Servicing the Spark Plug (page 16).
-
Page 19: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The engine does not start. 1. The engine switch is in the O 1. Move the switch to the O position. position. 2. The spark-plug wire is loose or 2. Install the wire on the spark plug. disconnected. - Page 20 Notes:...
- Page 21 Notes:...
- Page 22 Notes:...
- Page 23 Toro does not assume, and does not authorize any other person to assume for Toro, any liability in connection with the sale of Toro products. To be at "No Charge," warranty work must be sent directly to and performed by Toro or an Toro Authorized Warranty Service Facility.
- Page 24 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.