Toro 2024 Directional Drill Software Manual
Hide thumbs
Also See for 2024 Directional Drill:
- Operator's manual (100 pages) ,
- Operator's manual (23 pages)
Advertisement
Quick Links
2024 Directional Drill
Model No. 23800—Serial No. 313000501 and Up
Model No. 23800A—Serial No. 315000001 and Up
Model No. 23800C—Serial No. 315000001 and Up
Model No. 23800TE—Serial No. 315000001 and Up
Model No. 23800W—Serial No. 315000001 and Up
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely. Read your
Operator's Manual for more information.
Monitor
Home Screen Options
Main Information Screen
This is the first screen that appears after the initial
splash screen. To navigate between screens, use the
left and right arrows.
1. Drill speed (rpm)
2. Rotary torque
3. Thrust force
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Figure 1
4. Engine speed (rpm)
5. Drilling-fluid flow rate
6. Drilling-fluid pressure
Register at www.Toro.com.
1. Pipe functions
2. Fuel gauge
3. Limit setting options
4. Select pipe row
Push button 1 to switch between the pipe functions:
pull pipe, push pipe, neutral.
Push button 5 to switch between thrust force, drill
speed (rpm), and rotary torque.
Use buttons 6 and 7 to set limits for the drill speed
(rpm), rotary torque, and thrust force.
g207713
Original Instructions (EN)
Form No. 3413-630 Rev B
Software Guide
Figure 2
5. Engine temperature gauge
6. Engine droop
7. Horn
8. Thrust force, drill speed
(rpm), or rotary torque
adjustment
All Rights Reserved *3413-630* B
Printed in the USA
g207712
Advertisement
Related Manuals for Toro 2024 Directional Drill
Summary of Contents for Toro 2024 Directional Drill
- Page 1 Form No. 3413-630 Rev B 2024 Directional Drill Model No. 23800—Serial No. 313000501 and Up Model No. 23800A—Serial No. 315000001 and Up Model No. 23800C—Serial No. 315000001 and Up Model No. 23800TE—Serial No. 315000001 and Up Model No. 23800W—Serial No. 315000001 and Up...
- Page 2 Pulling Pipe in SmartTouch Mode Start the SmartTouch mode with the cam assembly in the home position (row 3 of the pipe box). Important: Ensure that you hold the lower section of the cam rocker switch, on the left joystick, completely down until the action is complete in each step (Figure...
- Page 3 Push buttons 2 and 3 to select the row where you want to place the pipe (Figure g210062 Figure 6 1. Pull pipe 2. Select pipe row Hold the lower section of the rocker switch (Figure 8) until the elevator lowers, the cam assembly rotates toward the operator station, and the arms fully extend (Figure...
- Page 4 Hold the upper button on the joystick to grip the pipe (Figure 11 Figure 12) and release the button. g210462 Figure 14 g210533 Figure 11 g210521 Figure 15 Release the rocker switch to proceed to the next step in the sequence (Figure 16).
- Page 5 Hold the lower section of the rocker switch Hold the lower section of the rocker switch (Figure 17) until the cam assembly rotates to the (Figure 20) until the elevator puts the pipe back selected row under the pipe box (Figure 18).
- Page 6 Pushing Pipe in SmartTouch Mode Push button 1 to select push pipe (Figure 24). Push buttons 2 and 3 to select the row where Start the SmartTouch mode with the cam assembly in you want to get the pipe (Figure 24).
- Page 7 Hold the lower section of the rocker switch (Figure 29) until the cam assembly fully rotates forward to the rack and the elevators lift the remaining pipe into the pipe box (Figure 30). g210462 Figure 26 g210462 Figure 29 g210463 Figure 27 Release the rocker switch to proceed to the next step in the sequence...
- Page 8 Hold the lower section of the rocker switch Hold the lower button on the joystick (Figure (Figure 32) until the arms extend (Figure 33). 35) to release the pipe (Figure 36) and release the button. g210462 g210527 Figure 32 Figure 35 g210528 Figure 33 g210529...
- Page 9 Hold the lower section of the rocker switch Release the rocker switch to start the push-pipe (Figure 38) until the arms retract and the cam process again. The cam assembly will go to assembly returns to the home position (row 3) the row picked in step Pulling Pipe in (Figure...
- Page 10 Drilling Fluid (Mud) Use Screen Lubrication and Maintenance Screens To access this screen push button 2 on the Hours To access this screen, push button 3 on the Hours screen. screen. This screen shows the drilling fluid (mud) use of the These screens provide the user with the daily machine.
- Page 11 g034778 g034781 Figure 43 Figure 46 g034779 Figure 44 g034780 Figure 45...
- Page 12 Settings Screen Options Push Pipe: refer to Starting the First Pipe and Adding Drill Pipes in the Drilling the Bore section in your Operator’s Manual for full instructions. Carriage Settings Screen Pull Pipe: refer to Removing Drill Pipes in the Drilling Push button 1 on the Settings screen.
- Page 13 Maintenance and Parameters Options Screen Screen Settings Screen Push button 3 on the Settings screen. Push button 6 on the Settings screen to switch between zoom delay, brightness, and day or night Push the up and down arrows to switch between mode.
- Page 14 The carriage indicates a range from 0.0 to 10.0 volts in the joystick selected direction for thrust or If the engine is off, the voltage is measured by the pullback. Toro controller. • The lower left icon indicates the carriage position Engine temperature: displays the engine coolant of wrench, load, or carriage back as the carriage temperature.
- Page 15 Cam Arm I/O Screen Auxiliary I/O Screen To access this screen push button 3 on the I/O screen. To access this screen push button 5 on the I/O screen. Use this screen to adjust the cam calibration options. All icons change from black to green when you operate the associated functions.
- Page 16 Controller I/O Screen Travel Pendant I/O Screen To access this screen push button 6 on the I/O screen. To access this screen push button 7 on the I/O screen. The travel pendant screen shows the voltage and position of the joystick located on the pendant. g204521 Figure 58 g034772...
- Page 17 Errors and Machine Information Machine Information Screen Screens To access this screen push button 3 on the Errors and Machine Information screen. Drill Errors Screens This screen displays the machine information including the model, serial number, and software To access this screen push button 1 on the Errors and version.
- Page 18 Notes:...
- Page 19 Notes:...