Cisco 7010 Replacement Instructions Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Switch
  5. TelePresence Server 7010
  6. Replacement instructions manual
Cisco 7010 Replacement Instructions Manual

Cisco 7010 Replacement Instructions Manual

600w ac-input power supply and fan tray replacement
Hide thumbs Also See for 7010:
Table of Contents

Advertisement

Quick Links

Download this manual
Doc. No.
78-1233-02
600W AC-Input Power Supply and Fan Tray
Replacement Instructions
Cisco 7010 Product Numbers: PWR-7010AC= and ACS-7010FAN=
Cisco 7505 Product Numbers: PWR/5-AC= and MAS/5-FAN=
Customer Order Number: DOC-781233=
This document contains instructions for replacing the 600W, AC-input power supply and the fan tray,
both of which are available as spare parts for the Cisco 7010 and Cisco 7505 chassis.
Note
The sections in this document include the following:
•
•
•
•
Copyright © 1995
Cisco Systems, Inc.
All rights reserved.
When referring to both the Cisco 7010 and Cisco 7505 chassis, chassis will be used.
Product Overview, page 2
Prerequisites, page 6
Replacing Components, page 8
— Removing and Replacing the Chassis Cover Panel, page 9
— Removing and Replacing the Fan Tray, page 10
— Removing and Replacing the Power Supply, page 12
Cisco Information Online, page 17
1

Advertisement

Table of Contents
loading

Related Manuals for Cisco 7010

Summary of Contents for Cisco 7010

  • Page 1 Customer Order Number: DOC-781233= This document contains instructions for replacing the 600W, AC-input power supply and the fan tray, both of which are available as spare parts for the Cisco 7010 and Cisco 7505 chassis. Note When referring to both the Cisco 7010 and Cisco 7505 chassis, chassis will be used.

  • Page 2: Product Overview

    Route Switch Processor (RSP1) is a required system component and occupies the top slot. In both chassis, the remaining interface slots (three in the Cisco 7010 and four in the Cisco 7505) support any combination of available interface types: Ethernet, Token Ring, FDDI, serial, HSSI, and so forth.
  • Page 3 Fan tray Power Supply The Cisco 7010 and Cisco 7505 come equipped with one 600W, AC-input power supply. Table 1 lists the power specifications for the Cisco 7010 and Cisco 7505. The following sections describe the 600W, AC-input power supply and the fan tray. For descriptions of other system components, refer to the Cisco 7010 Hardware Installation and Maintenance or Cisco 7505 Hardware Installation and Maintenance publications.
  • Page 4 Product Overview Frequency 50 to 60 Hz Power distribution 70A maximum @ +5 VDC, 15A maximum @ +12 VDC, 3A maximum @ –12 VDC, and 5A maximum @ +24 VDC On the noninterface processor end of the power supply, two handles provide grip points for pulling the power supply out of the chassis.
  • Page 5 Product Overview Fan Tray The fan tray comprises six individual axial fans and a printed circuit board (with the control circuits) mounted on a metal plate. (See Figure 2.) The fans draw cooling air through the chassis interior to maintain an acceptable operating temperature for the internal components. The fan tray slides into the right side of the chassis from the noninterface processor end of the router.

  • Page 6: Safety Guidelines

    Prerequisites Prerequisites Before you begin this installation, review the safety guidelines in this section to avoid injuring yourself or damaging the equipment. This section also provides a list of the tools that you need to perform this replacement. Safety Guidelines When working with any electrical equipment, the following guidelines will help to ensure your safety and protect the equipment.

  • Page 7: Tools And Equipment

    If a power strip or other equipment obstructs access, you will have to remove the chassis from the rack before replacing the component. Refer to the Cisco 7010 Hardware Installation and Maintenance or Cisco 7505 Hardware Installation and Maintenance publications for the tools you will need and descriptions of the rack mounting hardware.

  • Page 8: Replacing Components

    Replacing Components Preventing Electrostatic Discharge (ESD) Damage Electrostatic discharge (ESD) damage, which can occur when electronic boards or components are handled improperly, can result in complete or intermittent failures. The RP, SP, and interface processors each comprise a printed circuit board that is fixed in a metal carrier. EMI shielding, connectors, and a handle are integral components of the carrier.
  • Page 9 Replacing Components Removing and Replacing the Chassis Cover Panel The two captive slotted screws are the only fasteners on the cover panel. (See Figure 5.) Five shallow tabs at the bottom edge of the panel fit into slots at the base of the chassis opening. The tabs act as a pivot point for pulling the top of the panel away from the chassis opening, and as guides to align the panel when replacing it.

  • Page 10: Removing And Replacing The Fan Tray

    Replacing Components Removing and Replacing the Fan Tray When viewing the chassis from the noninterface processor end, the fan tray is on the far right. (See Figure 2.) A cutout in the front of the tray provides a handle for pulling the tray out of the chassis. An M4 Phillips screw anchors a tab on the lower left side of the tray to the interior chassis frame, just below the right power supply ear.
  • Page 11 Replacing Components Figure 6 Replacing the Fan Tray Removing/replacing fan tray Step 6 Insert the top runner of the fan tray through the notch in the top of the chassis. Continue pushing the tray into the chassis, and ensure that the bottom runner slides into the track on the floor of the chassis.

  • Page 12: Removing And Replacing The Power Supply

    Replacing Components Figure 7 Fan Tray Tracks and Guides L-bracket Fan tray, side view Fan tray, side view Card cage Chassis enclosure Bottom runner Track Step 9 Follow Steps 3 through 6 in “Removing and Replacing the Chassis Cover Panel” on page 9 to replace the cover panel.
  • Page 13 Follow Steps 1 and 2 in the section “Removing and Replacing the Chassis Cover Panel” on page 9 to open the chassis. The Cisco 7010 and Cisco 7505 have slightly different power harness covers, but for both Note chassis, this cover and power harness must be removed to access the power supply.
  • Page 14 Replacing Components Replacing the Power Supply, Power Harness, and Power Harness Cover Follow these steps to remove the power harness cover and power supply: Step 1 On the interface processor end of the power supply, remove the cable retention clip from the AC receptacle (or tape it up out of the way);...
  • Page 15 Replacing Components Figure 9 Replacing the Power Supply Power supply ears Power harness Phillips screws (2 places) Backplane power receptacle Removing/replacing power supply Handling the power supply Warning Disconnect the power harness by pulling on the connector plug; do not pull or tug on the harness wires.

  • Page 16: Checking The Installation

    (For descriptions and examples of these commands, refer to the section “Prerequisites” on page 6.) This completes the fan tray and power supply replacement procedures for the Cisco 7010 and Cisco 7505. 16 600W AC-Input Power Supply and Fan Tray Replacement Instructions...

  • Page 17: Cisco Information Online

    LAN/X.25, Point and Click Internetworking, SMARTnet, SynchroniCD, The Packet, UniverCD, WNIC, Workgroup Director, Workgroup Stack, and XCI are trademarks; Access by Cisco and Bringing the power of internetworking to everyone are service marks; and Cisco, Cisco Systems, the Cisco logo, EtherSwitch, and Kalpana are registered trademarks of Cisco Systems, Inc. All other trademarks, service marks, registered trademarks, or registered service marks mentioned in this document are the property of their respective owners.

This manual is also suitable for:

7505

Table of Contents