Advertisement
Quick Links
Switch Panel
Groundsmaster
Sunshade
Model No. 03248
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
and Reelmaster
Description
No parts required
No parts required
Decal
Switch panel
Fuse-block mount
Wire harness
Socket-head screw (#10 x 3/4 inch)
Flange locknut (#10)
Carriage bolt (#10 x 1/2 inch)
Carriage bolt (#10 x 1/2 inch)
Flange locknut (#10)
Cable tie
No parts required
No parts required
No parts required
Register at www.Toro.com.
Form No. 3434-525 Rev A
®
Traction Units with Universal
Installation Instructions
Qty.
–
Prepare the machine.
–
Remove the sunshade.
1
Prepare the switch panel.
1
1
1
Assemble the wire harness to the switch
2
panel.
4
2
4
Installing the switch panel to the
4
sunshade frame.
6
–
Install the sunshade.
–
Connect the wire harness.
–
Connect the battery.
Original Instructions (EN)
All Rights Reserved *3434-525* A
Printed in the USA
Use
Advertisement
Related Manuals for Toro 03248
Summary of Contents for Toro 03248
- Page 1 Form No. 3434-525 Rev A Switch Panel Groundsmaster ® and Reelmaster ® Traction Units with Universal Sunshade Model No. 03248 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty.
-
Page 2: Preparing The Machine
Preparing the Machine No Parts Required Procedure Park the machine on a level surface. Shut off the engine, engage the parking brake, and remove the key from the ignition switch. Disconnect the battery; refer to the electrical system maintenance section of your Operator’s Manual. - Page 3 Assembling the Wire Harness to the Switch Panel Parts needed for this procedure: g245155 Fuse-block mount Figure 3 Wire harness 1. Rectangular opening 3. Rectangular opening (decal) (switch panel) Socket-head screw (#10 x 3/4 inch) 2. Hole (decal) 4. Hole (switch panel) Flange locknut (#10) Carriage bolt (#10 x 1/2 inch) Align the rectangular openings and hole in the...
- Page 4 Assemble the fuse-block mount to the fuse block (Figure 5) with the 2 socket-head screws (#10 x 3/4 inch) and 2 flange locknuts (#10). Torque the socket-head screws and flange-locknuts to 419 to 513 N∙cm (37 to 47 in-lb). Assembling the Wire Harness to the Switch Panel Align the wire harness to the switch panel (Figure...
- Page 5 Torque the flange-locknuts to 419 to 513 N∙cm (37 to 47 in-lb). Routing the Wire Harness Installing the Switch Panel Route the wire harness of the switch panel kit to the Sunshade Frame along the roll-bar tube as shown in Figure Parts needed for this procedure: Carriage bolt (#10 x 1/2 inch)
- Page 6 g246397 Figure 12 Groundsmaster 5900 Machines g245179 For Groundsmaster 5900 machines, raise the Figure 10 hood; refer to the Operator’s Manual for your 1. Sunshade 3. Washer (5/16 inch) machine. 2. Flange-head bolt (5/16 x 4. Clip nut (side-frame If installed, remove the cap from the 2-socket 1-1/4 inches) channel) connector of the machine wire harness...
-
Page 7: Connecting The Battery
g246395 Figure 14 Groundsmaster 4000 Series Machines 2. 2-socket connector 1. 2-pin connector (kit wire harness) (machine wire harness) For Groundsmaster 5900 machines, lower the hood; refer to the Operator’s Manual for your machine. Connecting the Wire Harness to the Optional Power Harness Kit Groundsmaster 360, Groundsmaster 3000 Series, Groundsmaster 4500 Series and 4700 Series, Groundsmaster 7200 Series;...