NEC DS2000 Instructions
Hide thumbs
Also See for DS2000:
- Feature handbook (208 pages) ,
- Hardware manual (78 pages) ,
- Release notes (44 pages)
Advertisement
Quick Links
DS2000 PC Card Instructions for Backup,
Restore, and Software Upgrade
Use PC Card P/N 85880 to back up and restore your site data. Use PC Card P/N 80051-V**.** to load or update
your system's software. (Note that **.** denotes the level of the system software loaded on PC Card P/N 80051.)
Backing Up Site Data
To use PC Card P/N 85880 to back up site data:
1. Insert PC Card P/N 85880 into the CPU (see the figure
at right).
2. Be sure the CPU mode switch is set to
3. Enter the programming mode.
ICM + #*#* + 372000 + HOLD
4. Dial 9906 + HOLD.
You see: START?
To quit program 9906 instead of going to the next step,
dial N + HOLD.
5. Dial Y + HOLD.
You see: 9906: DATABASE NAME
6. Enter a name for the database you want to save (up to
10 characters long).
Refer to Name Programming at right if you need help
when entering names.
Skip this step if you want to save data in an address
that already has a name assigned.
7. When you are done entering the name, press HOLD.
You see the name and date of the first database stored.
If no databases are stored, you see: 9906: DB00
(empty)
8. The system assigns the name you entered in step 7 to
the address you select below:
▲
Press VOL
or VOL
base addresses (DB 00 through DB 15).
OR
Skip this step to select the currently displayed data
base.
9. Press HOLD.
Normally, you see 9906: SAVING . . . . . . . . .
The PC Card Active LED is on during backup.
If the address you choose already has data stored in it,
you see: REPLACE DB nn Y/N.
- Press N + HOLD to back up to step 5.
- Press Y + HOLD to proceed.
You automatically exit programming when the backup
completes.
PC Card P/N 80051 is a system software PC Card only.
You cannot use it to back up and restore site data.
RUN
▼
to scroll through the 16 data
Mode Switch
.
PC Card Active
LED
Key
1 Time
1
&
2
A
3
D
4
G
5
J
6
M
7
P
8
T
9
W
0
space
#
*
After selecting a letter, press a key for another letter or wait 2 seconds for the cursor to automatically advance.
HOLD
Save name. In system programming, HOLD saves and exits name programming.
CONF
Exit name programming without saving name.
VOL Up
Scroll the cursor to the left.
VOL Dn
Scroll the cursor to the right.
MW
Put the cursor after the last entry.
LND
Delete the character under the cursor.
FLASH
Delete the character to the right of the cursor.
CLEAR
Clear the entire entry.
CHECK
Restore the previous entry,
Name Programming
Press a key the indicated number of times for desired character
2 Times
3 Times
4 Times
5 Times
6 Times
-
/
'
1
B
C
a
b
E
F
d
e
H
I
g
h
K
L
j
k
N
O
m
n
Q
R
S
p
U
V
t
u
X
Y
Z
w
:
0
Not used
Not used
Additional Name Programming Options
7 Times
8 Times
9 Times
c
2
f
3
i
4
l
5
o
6
q
r
s
7
v
8
x
y
z
9
Continued
Advertisement
Related Manuals for NEC DS2000
Summary of Contents for NEC DS2000
- Page 1 DS2000 PC Card Instructions for Backup, Restore, and Software Upgrade Use PC Card P/N 85880 to back up and restore your site data. Use PC Card P/N 80051-V**.** to load or update your system’s software. (Note that **.** denotes the level of the system software loaded on PC Card P/N 80051.) PC Card P/N 80051 is a system software PC Card only.
- Page 2 7. When the database you want to restore displays, press HOLD. The PC Card Active LED is on during restore. The system will automatically reset when the restore completes. NEC Unified Solutions, Inc. 4 Forest Parkway, Shelton, CT 06484 *85880INS06*...