Table of Contents
Advertisement
RTU560
Connections and Settings
Communication Unit 560CMD11
Application, characteristics and technical data
have to be taken from the hardware data sheet:
560CMD11 R0001
560CMD11 R0011
Operation
The Communication Unit 560CMD11 is one of the
CMU boards (CMU = communication unit) of the
remote terminal unit RTU560. The 560CMD11
controls process events and communications with
control centers and local MMI systems via up to
four serial Interfaces (CP1, CP2, CPA, CPB), two
Ethernet 10BaseT/100BaseT LAN Interfaces (E1,
E2) and an integrated GPRS modem.
Fig. 1: Block diagram 560CMD11
To force the IP-Address to a default value at start-
up, the "Def. IP-Addr" switch on the front side (see
has
to
Fig.
8)
The 560CMD11 starts with the factory settings for
the Ethernet Interface (see Fig. 2) which are
192.168.0.1 for the IP-address with the network
Doc.-No.: 1KGT 150 765 V005 1
1KGT 150 764 V0011
1KGT 150 764 V0011
be
switched
"ON".
setting 255.255.255.0 for the subnet mask and
192.168.0.20 for the gateway.
Switch „Def. IP- Address"
Switch „Def. IP- Address"
ON
ON
position
position
?
?
Send Configuration
Send Configuration
to RTU 192.168.0.1
to RTU 192.168.0.1
Set Switch
Set Switch
„Def. IP-Address"
„Def. IP-Address"
to „OFF"
to „OFF"
E
E
Fig. 2: Use Switch „Def. IP-Addr"
Serial Interface
The serial interfaces (CP1, CP2, CPA and CPB)
are available on the RJ45 connector on the front
plate. It can interface RS485 (Tab. 1) or RS232C
(Tab. 2) signals.
Serial Interfaces RS485 Mode
Pin
Signal
1
-
2
TA
3
TB
4
-
5
GND
6
-
7
-
8
-
Table 1: Serial Interfaces RS485 Mode
OFF
OFF
Read IP address
Read IP address
from confi-
from confi-
guration file
guration file
Not used
Data -
RJ45
RJ45
RJ45
Data +
Rx
Rx
Not used
Tx
Tx
Signal Ground
Jack
Not used
1
1
1
8
8
8
1
Advertisement
Table of Contents
Related Manuals for ABB RTU560
Summary of Contents for ABB RTU560
-
Page 1: Serial Interface
Read IP address CMU boards (CMU = communication unit) of the Send Configuration Send Configuration from confi- from confi- remote terminal unit RTU560. The 560CMD11 to RTU 192.168.0.1 to RTU 192.168.0.1 guration file guration file controls process events and communications with... - Page 2 Following antennas are recommended: The settings have to be done by the RTUtil560 560ANA01 bar (dipole) antenna configuration tool. ABB number: 1KGT023600R0001 At the CPA and CPB interfaces different UART 560ANA02 Wall-mount antenna connect- character based protocol types can be used.
- Page 3 RTU560 Connections and Settings Communication Unit 560CMD11 Ethernet Interface E1 and E2 Power Supply DC- In The Ethernet Interfaces are available on a RJ45 The supply voltage for the 560CMD11 is 24VDC. The connector consists of a 3 pole pluggable connector and supports different functions: ...
- Page 4 The power supply terminal X38-2 (-) is internal The red LED of the 560CMD11 is controlled by connected with the housing ground by terminal the RTU560 firmware. For the definition and oper- X43 (see Fig. 3). ation of the LED “ERR" please refer to the release The protection earth must be connected to screw specific function description.
-
Page 5: Power System
RTU560 Connections and Settings Communication Unit 560CMD11 560CMD11 System 560PSU40/41 power supply GPRS Chip Fig. 4: Negative System Earthing RS232 galvanic 560CMD11 System isolated power supply GPRS Chip 560PSU40/41 Fig. 5: Positive System Earthing Doc.-No.: 1KGT 150 765 V005 1... - Page 6 RTU560 Connections and Settings Communication Unit 560CMD11 SIM-Card (only R0011) Firmware Version For communication via the GSM/GPRS modem a pluggable SIM-Card (ID-000) is necessary. The current firmware version will be delivered on For changing the SIM-Card the right side of the a CompactFlash memory card.
- Page 7 RTU560 Connections and Settings Communication Unit 560CMD11 Settings For the configuration procedure of the GPRS- Modem (only R0011), please refer to the function Hardware settings and operation of the communi- description part 6. cation Interfaces of the 560CMD11 are carried out with the RTUtil560 configuration tool.
- Page 8 RTU560 Connections and Settings Communication Unit 560CMD11 Fig. 7: Top side of 560CMD11 R0001 housing screws screws Fig. 8: Front and right side of 560CMD11 R0001 housing Fig. 9: Bottom side of 560CMD11 R0001 housing Doc.-No.: 1KGT 150 765 V005 1...
- Page 9 RTU560 Connections and Settings Communication Unit 560CMD11 Ethernet Fig. 10: Top side of 560CMD11 R0011 housing screws screws Fig. 11: Front and right side of 560CMD11 R0011 housing Fig. 12: Bottom side of 560CMD11 R0011 housing Doc.-No.: 1KGT 150 765 V005 1...
- Page 10 We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB AG does not accept any responsibility whatsoever for potential errors or possible lack of information in this document.