Table of Contents
Advertisement
Quick Links
TABLE OF CONTENTS....................................................... 2
1 REGULATION................................................................. 3
2 THE ERF2000-PANEL...................................................... 3
3 ERF2000-FUNCTIONS..................................................... 4
4 SPECIAL FUNCTIONS..................................................... 6
5 MANUAL DEFROSTING................................................... 6
6 DISASSEMBLY COLD MODULE........................................ 7
7 SENSORS..................................................................... 9
8 PRINTED CIRCUIT BOARD (PCB)..................................... 10
This instruction replaces publication no.
599 xx xx-xx
©DISTRIPARTS AB
BOX 501
S-562 80 NORRAHAMMAR
TEL 036-31 80 00
Telefax 036-31 81 10
Telefax 036-31 80 88
Publication number
599 51 83-06
03-10-21
SV/SERVICE
DT/MA/AN
SERVICE INSTRUCTION
FREEZER
NOFROST
ERF2000
COLD
21
B
Advertisement
Table of Contents
Related Manuals for Electrolux ERF2000
Summary of Contents for Electrolux ERF2000
-
Page 1: Table Of Contents
SERVICE INSTRUCTION COLD TABLE OF CONTENTS………………………………………………. 2 1 REGULATION……………………………………………………….. 3 2 THE ERF2000-PANEL……………………………………………... 3 3 ERF2000-FUNCTIONS………………………………………….…. 4 4 SPECIAL FUNCTIONS…………………………………………….. 6 5 MANUAL DEFROSTING…………………………………………… 6 6 DISASSEMBLY COLD MODULE………………………….……… 7 7 SENSORS…………………………………………………………… 9 8 PRINTED CIRCUIT BOARD (PCB)………………………………. 10 This instruction replaces publication no. -
Page 2: Table Of Contents
3.3 Displaying the temperature 3.4 Action Freeze / Freezing 3.5 Temperature alarm 3.6 Door alarm 3.7 Door switch 3.8 Error indication on the ERF2000 panel 4. Special functions 4.1 Cooler mode 4.2 Super cooling 4.3 Demo mode 5. Manual defrosting 6. -
Page 3: Regulation
• When the door is opened the fan stops immediately. When starting the cabinet when the temperature inside is warmer than 0°C, the defrosting starts 8 minutes after start. 2. The ERF2000 panel ACTION FREEZE A B C D E... -
Page 4: Erf2000-Functions
• When the refrigerator is restarted the temperature needs not to be reselected. The ERF2000 electronic is automatically set on the latest selected temperature. 3.3 Displaying the temperature • The thermometer displays temperatures between -39°C and +39°C 3.4 Action Freeze / Freezing... -
Page 5: Temperature Alarm
"Reed-element" (a) on the PCB and a magnet (b) on the door (in the middle of the upper side of the door). See picture: 3.8 Error indication on the ERF2000 panel Air sensor defective: Thermometer lower right part shows: Evaporator sensor defective:... -
Page 6: Special Functions
4.Special functions 4.1 Cooler mode (Only AEG) For products in AEG design there is a possibility change the regulation so that the products could be used as a refrigerator. This function is activated by simultaneously pressing the reset button for alarm and the temperature selector button for colder temperature for 5 seconds. -
Page 7: Disassembly Cold Module
6. Disassembly cold module 1. Remove the 3 upper shelves, with flaps and drawers. 2. Unscrew the 5 screws in the bottom of the module (picture 1), and remove the cover and the insulation. 3. Turn the holder for the upper ail channel 90°... - Page 8 Connection of components (picture 5): E. Evaporator sensor (brown) C. Air sensor (white) F. Fan B. Defrost heater The reassemble is done in the opposite order. NOTE! Before the cover, the insulation and the upper air channel is reassembled, check that the cage (G) for the drainage hose is not loose from from the module (H).
-
Page 9: Sensors
7.Sensors 7.1 General The freezer contains two temperature sensors, NTC, for measure of the temperature. One sensor is placed in the air and the other on the evaporator. Air sensor, white wiring Evaporator sensor, brown wiring The sensors characteristic are shown below. Resistance –... -
Page 10: Printed Circuit Board (Pcb)
8.Printed Circuit Board (PCB) 8.1 Exchange of PCB At exchange of the PCB, chassis complete with PCB shall always be exchanged. Operations at the exchange of PCB: Open the control panel by…. There are 4 types of control panels, A,B,C,D, see pictures to the left. For type A and B: Loosen the pivot pin from above.