Table of Contents
Advertisement
Quick Links
Register at www.Toro.com.
Original Instructions (EN)
8-Blade, 11-Blade, and 14-Blade
DPA Reel Mower
Greensmaster
Traction Unit
Model No. 04652—Serial No. 316000001 and Up
Model No. 04654—Serial No. 316000001 and Up
Model No. 04656—Serial No. 316000001 and Up
Form No. 3397-897 Rev A
®
3120, 3150, or 3250-D Series
*3397-897* A
Advertisement
Table of Contents
Related Manuals for Toro 04652
Summary of Contents for Toro 04652
- Page 1 DPA Reel Mower Greensmaster ® 3120, 3150, or 3250-D Series Traction Unit Model No. 04652—Serial No. 316000001 and Up Model No. 04654—Serial No. 316000001 and Up Model No. 04656—Serial No. 316000001 and Up *3397-897* A Register at www.Toro.com. Original Instructions (EN)
- Page 2 You are responsible for operating the if you do not follow the recommended precautions. product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product.
-
Page 3: Table Of Contents
Authorized Toro Distributor. • To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous, and such use could void the product warranty. -
Page 4: Hauling
Hauling • Use full-width ramps for loading the machine into a trailer or a truck. • Use care when loading or unloading the machine into a • Tie the machine down securely using straps, chains, cable, trailer or a truck. or ropes. -
Page 5: Setup
Setup Media and Additional Parts Description Qty. Ball stud Mount this to the roller. Operator's Manual Read before installing and operating the cutting unit. Parts catalog Use this to reference part numbers. Installing the Roller 7. Tighten the roller-mounting screws (Figure The cutting unit is shipped without a front roller. -
Page 6: Repositioning The Counter Weights
Torque the screws to 16 to 20 N∙m (12 to 15 ft-lb). G020065 Figure 6 1. Offset lift hook • Optionally for the Greensmaster 3250-D traction units, you can install the chain Link (Part No. 106-2601) and mounting bracket (Part No. 105-5738) available from your Toro Distributor. -
Page 7: Adjusting The Cutting Unit
Figure 8 1. Drive spline 3. Allen head screw 2. Motor mount 5. On the right end of the cutting unit, apply a light coating of oil to the O-ring and install the counter weight with the bolts previously removed (Figure Torque the screws to 16 to 20 N∙m (12 to 15 ft-lb). -
Page 8: Product Overview
8 Blade—30 kg (65 lb), 11 Blade—31 kg (68 lb), 14 Blade—32 kg (71 lb) Attachments/Accessories A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories. -
Page 9: Maintenance
Adjusting the Bedknife-to-Reel cutting (Refer to the Toro Manual for Sharpening Reel and Rotary Mowers, Form No. 09168SL). Contact Important: Light contact is preferred at all times. -
Page 10: Adjusting The Rear-Roller Height
(Figure 10). achieve the sharp edges needed for precision cutting (Refer to the Toro Manual for Sharpening Reel and Rotary Mowers, Form 3. Rotate the reel so that 1 of the blades crosses the No. 09168SL). bedknife edge between the first and second bedknife screw heads located on the right side of the cutting unit. -
Page 11: Adjusting The Height Of Cut
4. Place the spacers onto the screws above or below the roller brackets, as required (Figure 13 Figure 14). 5. Secure the roller bracket and spacers to the underside of the mounting flanges with the nuts previously removed. Note: The position of the rear roller to the reel is controlled by the machining tolerances of the assembled components and paralleling is not required. -
Page 12: Adjusting The Cut-Off Bar
Ideally, take the cutting unit to your Authorized Toro Distributor for service. Refer to the Service Manual for 6. Tighten the nuts to secure the adjustment enough to your traction unit for complete instructions, special tools, remove play from the washer. - Page 13 g020056 Figure 21 1. Bedbar bolt 3. Nylon washer 2. Nut 4. Steel washer Figure 19 Assembling the Bedbar 1. Bedbar-adjusting screw 3. Bedbar 2. Spring-tension nut 4. Washer 1. Install the bedbar, positioning the mounting ears between the washers and the bedbar-adjusting screw (Figure 22).
-
Page 14: Bedknife Specifications
Installation order: Note: Additional instructions and procedures on Backlapping are available in your traction unit Operator’s Manual and the Toro Sharpening Reel and Rotary Mowers Manual, Form Number 80-300PT. Figure 24 Note: For a better cutting edge, run a file across the front face of the bedknife and reel when the lapping operation is completed. - Page 15 Notes:...
- Page 16 Notes:...
- Page 17 Notes:...
- Page 18 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 19 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
- Page 20 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.