Related Manuals for Toro 08766
Summary of Contents for Toro 08766
- Page 1 Form No. 3391-605 Rev A Sports Field Edger Sand Pro ® 3040 and 5040 Traction Unit Model No. 08766—Serial No. 315000001 and Up *3391-605* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
You are responsible for operating the product properly and safely. Serial No. You may contact Toro directly at www.Toro.com for product This manual identifies potential hazards and has safety and accessory information, help finding a dealer, or to register... -
Page 3: Safety
Become familiar with all of the controls and know how to stop quickly. A free replacement manual is available by sending the complete Model and Serial Number to The Toro® Company, 8111 Lyndale Avenue South, Bloomington, Minnesota 55420-1196. -
Page 4: Maintenance
• If the engine stalls or the machine loses headway and genuine parts. When it comes to reliability, Toro delivers cannot make it to the top of a slope, do not turn the replacement parts designed to the exact engineering machine around. -
Page 5: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 120-3450 1. Warning—read the Operator's Manual, keep bystanders a safe distance from the machine. -
Page 6: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Cross tube assembly Screw (3/8 x 3 inch) Mount the cross tube assembly. Flat washer Locknut (3/8 inch) Cutter head assembly Install the cutter head assembly. Hitch pin Hose guide Install the hose guide. -
Page 7: Mounting The Cross Tube Assembly
Mounting the Cross Tube Assembly Parts needed for this procedure: Cross tube assembly Screw (3/8 x 3 inch) Figure 4 Flat washer Locknut (3/8 inch) 1. Cross tube assembly Procedure 2. Secure the cross tube mounting brackets to the frame tubes with 4 screws (3/8 x 3 inch), flat washers, and Note: If the Sand Pro is equipped with the mid-mount tool locknuts (3/8 inch) -
Page 8: Installing The Hose Guide
Figure 6 1. Hose guide 2. Hydraulic tank clamp Figure 5 2. Install the hose guide with the supplied flange nut. 1. Cross tube 3. Cutter head Position the hose guide as shown in Figure 2. Hitch pin 2. Secure the cutter head to the cross tube with the hitch (Figure Routing the Hydraulic Hoses No Parts Required... -
Page 9: Checking The Hydraulic Fluid
Checking the Hydraulic Fluid No Parts Required Procedure 1. Park the machine on a level surface. Figure 9 2. Stop the machine, move the throttle control to the Slow 1. Dipstick 2. Full mark position, rotate the ignition key to Off, and remove the key from the switch to prevent accidental starting. -
Page 10: Product Overview
Product Overview Operation Note: Determine the left and right sides of the machine Controls from the normal operating position. Handle Operating the Edger Use the handle to raise and lower the edger (Figure 10). 1. Start the engine. 2. Press outward on the handle and lower the edger blade to the ground (Figure 10). -
Page 11: Using The Alignment Guide
Figure 13 1. Roller 3. Scraper rod 2. Roller shaft 4. Remove the roller shaft from the roller (Figure 13). 5. Move the roller to the desired depth and install the shaft. Start at the low setting 1/2 to 1-1/2 inches. Note: Moving the roller down will raise the cutting depth. -
Page 12: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Lubricating the Edger The edger cutter head has a grease fitting that must be lubricated with #2 general-purpose, lithium-based grease after every 100 hours of operation (Figure 14). -
Page 13: Storage
Storage • Thoroughly wash the machine with a garden hose-without a nozzle-so that excessive water pressure will not cause contamination and damage to the seals and bearing • Check all fasteners for looseness; tighten as necessary. • Grease the fitting. Wipe off any excess lubricant •... - Page 14 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 15 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.