Advertisement
Time and day
Set the day
Set the time
Program the schedule
Skip a period
Select the mode
of operation
Indicates the
heating power
*
LP appears only for the first two minutes when the thermostat is without power. This
can occur during a power outage or when the thermal protection device inside the base-
board heater is opened.
Description
This programmable thermostat can be used to control an electric
heating system such as an electric baseboard heater, a radiant ceil-
ing, a radiant floor, a convector or a fan-forced heater.
The thermostat cannot be used with:
•
a resistive load over 16.7 A
•
a resistive load under 2 A
•
a system driven by a contactor or relay (inductive load)
•
a central heating system
SUPPLIED PARTS:
•
One (1) thermostat
•
Two (2) 6-32 screws
•
Two (2) solderless connectors
Installation
TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN
POWER PANEL TO AVOID ELECTRICAL SHOCK. THE INSTAL-
LATION MUST BE PERFORMED BY AN ELECTRICIAN.
All cables and connections must conform to the local electrical
code.
Special CO/ALR solderless connectors must be used when con-
necting with aluminum conductors.
Install the thermostat onto an electrical box.
Install the thermostat about 5 feet high, on an inside wall facing
the heater.
Avoid locations where there are air drafts (such as the top of a
staircase or an air outlet), dead air spots (such as behind a
door), or direct sunlight.
Do not install the thermostat on a wall that conceals chimney or
stove pipes.
The thermostat wires are not polarized; either wire can be con-
nected to the load or to the power supply.
08060 / TH106 / TL6061
Programmable Thermostat - Installation and User Guide
Temperature
preset buttons
Indicates that the
temperature setpoint
is displayed
Indicates that the
settings are locked
Temperature
Indicates the current
mode of operation
Temperature
preset icon
Indicates that the
thermostat is configured
for a fan-forced heater
Indicates the current
period (appears in
automatic mode only)
Temperature
Indicates that the ther-
adjustment
mostat is without power *
buttons
NOTE:
Always keep the thermostat's vents clean and unobstructed.
Connect the thermostat wires to the line wires and to the load
wires using solderless connectors for copper wires.
2-wire installation
1.
4-wire installation
2.
Push any excess wire back into the electrical box.
NOTE:
If necessary, before re-installing the front component, config-
ure the thermostat (see section 3).
Return power to heating system.
08160
TH106
TL6160
69-2202-04
2010-04-06
1/4
Advertisement
Related Manuals for Honeywell 8160
Summary of Contents for Honeywell 8160
- Page 1 08160 TH106 TL6160 NOTE: Always keep the thermostat's vents clean and unobstructed. Temperature preset buttons Indicates that the temperature setpoint is displayed Indicates that the Time and day settings are locked Set the day Temperature Indicates the current Set the time mode of operation Program the schedule Temperature...
-
Page 2: Temperature Setting
Configuration Temperature Setting Setpoint The configuration switches are on the back of The thermostat normally displays the actual temperature. To view the the thermostat. The factory settings are indi- setpoint, press the button briefly. The setpoint will appear for cated by the gray cells in the following table. the next 5 seconds. -
Page 3: Troubleshooting
Schedule Troubleshooting The schedule consists of 4 periods per day which represents a typi- cal weekday. You can program the thermostat to skip the periods that PROBLEM SOLUTIONS do not apply to your situation. For example, you can skip periods 2 and 3 for the weekend. -
Page 4: Customer Assistance
55422, or whether a replacement product can be sent to you. This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.